Sharp AR-C160 manual Printer KEY Operator Programs, Enable Bypass-Tray Size Detection

Page 35

KEY OPERATOR PROGRAMS

PRINTER KEY OPERATOR PROGRAMS

The following programs can be selected only if an optional power supply kit and an optional printer controller have been installed. Select “PRINTER” after entering the key operator code number. Then select the desired program.

Enable Bypass-Tray Size Detection

This program is used to enable or disable paper size detection of the bypass tray in the print mode. This setting does not affect the paper size detection in the copy mode.

●When the check mark is on, automatic size detection is enabled for the bypass tray and the tray is included as an alternative for auto tray switching for the print mode.

●When the check mark is off, the bypass is not included as an alternative for automatic tray switching and the paper in the bypass tray is always defined as special paper.

To enable paper size detection of the bypass tray in the print mode, press the “ENABLE BYPASS-TRAY SIZE DETECTION” box to display a check mark.

To disable paper size detection, press the checked box again to clear the check mark.

NOTE:

If images larger than the paper in the bypass tray are printed, the toner image outside the paper area will be wasted and will tend to dirty some machine parts. After disabling the size detection, be careful to print images that are the same size or smaller than the paper used.

Enable Bypass-Tray Type Detection

This program is used to ensure that the paper type selected for copying and printing are the same.

●When the check mark is on, the paper types selected for copying and printing will be compared. These must be the same for automatic paper feeding to function.

●When the check mark is off, the settings for copier and printer can be different and will not be compared. When the settings are different, a selection from the printer driver will override any selection made at the copier. When printing with the check mark off, make sure to select the correct paper type. Selecting a wrong paper type might cause a misfeed or other malfunction.

To enable paper type detection of the paper tray, press the check box of “ENABLE BYPASS- TRAY TYPE DETECTION” to display a check mark.

To disable it, press the checked box again to clear the check mark.

33

Image 35

Contents AR-C160 Page Contents Enter 0 five times using the 10-key pad Press the Custom Settings keyKEY Operator Code Number KEY Operator Programs KEY Operator Programs Printer KEY Operator Programs optional Press the Copier key or the Printer key on Touch panel Using the key operator programsEnter the key operator code number Follow instructions for the program Select the desired category on the touch panelPress the key of the desired program on the touch panel Press the OK key to exit the program Auditing ModeAccount Control Press the upper OK key to exit the program Number of Copies per AccountPress the key to advance through the accounts Billing by Account Press the key of an account to be reset Resetting AccountTo reset all accounts To reset a single accountPress the Enter key Account Number ControlTo register accounts To delete accountsPress the Print key Price/Copy SettingTo change an account number To print all registered account numbersSimilarly enter the prices for price codes #2 to #4 To set a limit for all accoounts Account Limit SettingTo set a limit Account Number Security Adjust the exposure using the and keys Other Function SettingsExposure Adjustment Toner Save Mode B/WUse the and keys to set the desired copy ratio Add or Change Extra Preset RatiosSetting a Maximum Number of Copies Input the number using the 10-key padAdjust the value for each side using the and keys Initial Margin Shift SettingErase Width Adjustment Press the Return to the Factory Default SETTINGS. key Initial Status SettingTo establish new initial settings To return to the factory default settingsSize Setting for Extra Initial Color Balance SettingSelect a paper tray on the touch panel Select a paper size for Extra settingRequire Key Operator Code Override Sorter Bin Capacity Limit Stream Feeding ModeEnter the time interval using Keys Press the OK key Timer SettingsSleep Mode Setting Auto Clear SettingSet the time using the and keys Press the OK key Preheat Mode SettingMessage Time Setting Disabling of Auto Paper Selection ENABLE/DISABLE SettingsDisabling of Beep When Keys Touched Disabling of Auto Tray SwitchingDisabling of Duplex Copying Disabling of Bypass-Tray in Duplex CopyDisabling Deletion of Job Programs Disabling of Document FeederDisabling of Stapler Disabling of Covers ModeDisabling of PC/Modem Access Disabling of Pre-scan in B/W Copy Disabling of Sleep ModePress the Copier key Other ProgramsTotal Count Program List PrintoutPress the Execute key Auto Color CalibrationPrinter KEY Operator Programs Enable Bypass-Tray Size DetectionEnable Bypass-Tray Type Detection Prohibit Bypass-Tray Selection Prohibit Auto Tray SwitchingKEY Operator Assistance Call Sharp Corporation

Related manuals

Manual 148 pages 6.18 Kb