Sharp MX-M282N Placing Originals, Using the automatic document feeder, Using the document glass

Page 21

PLACING ORIGINALS

The automatic document feeder can be used to automatically scan many originals at once. This saves you the trouble of manually feeding each original.

For originals that cannot be scanned using the automatic document feeder, such as a book or a document with notes attached, use the document glass.

Using the automatic document feeder

When using the automatic document feeder, place the originals in the document feeder tray. Make sure an original has not been placed on the document glass.

Adjust the original guides to the width of the originals.

Place the originals face up with the edges aligned evenly.

The indicator line indicates approximately how many originals can be placed. The placed originals must not be higher than this line.

Using the document glass

Take care that your fingers are not pinched when closing the automatic document feeder.

After placing the original, be sure to close the automatic document feeder. If left open, parts outside of the original will be copied black, causing excessive use of toner.

Place the original face down.

Align the top left corner of the original with the tip of the mark in the far left corner of the glass.

To place a thick original such as a book, push up the far edge of the automatic document feeder and then close the automatic document feeder slowly.

Place the original face down.

19

Image 21
Contents MX-M362N MX-M452N MX-M502N Start GuideGREEN-AND-YELLOW Earth EMC this machine and peripheral devicesNeutral LiveSoftware Licence WarrantyFor the users of the fax function FAX interface cable and Line cableContents Power notes Symbols in this manualDo not damage or modify the power cord Do not insert or remove the power plug with wet handsDo not install in a location with moisture or dust Installation notesLocations exposed to direct sunlight Locations with ammonia gasAbout consumables Near a wallLocations subject to vibration Do not use a flammable spray to clean the machine Handling precautionsDo not remove the machine casing Do not make any modifications to this machineLaser information Safety PrecautionsConvenient methods for using the Operation Guide Printed manuals Start GuideOperation Guide Opening the Web pages Access the Web server in the machine toDownloading the Operation Guide Open the Web pagesPress the System Settings key Select the all custom setting list in the touch panelChecking the IP Address Exterior Part Names and FunctionsPunch module USB connector a type Supports USB 2.0 Hi-SpeedSaddle stitch finisher Finisher large stackerInterior Automatic Document Feeder and Document Glass LAN connector When the fax expansion kit is installedUSB connector B type Supports USB 2.0 Hi-Speed Side and BackTouch panel JOB Status key Print mode indicators Image send indicatorsSystem Settings key Operation PanelPower key Main power indicatorPower Save key Numeric keysTurning the Power on and OFF Main power switch Power keyMain power indicator Power key Using the document glass Using the automatic document feederPlacing Originals Place the originals face up with the edges aligned evenlyPlain paper, special media Useable PaperTypes of paper that can be used in each tray Plain paper that can be usedBypass tray and tray Trays 1 toLoading Paper in a Tray Names of the traysLoading paper in a tray Configure the tray settings in the touch panel Changing the tray settingsLoading paper in other trays Bypass trayExample Loading an envelope Large capacity tray CD-ROMS and Software Before Installing the SoftwarePCL6 printer driver PS printer driver Sharpdesk/Network Scanner Utilities CD-ROM for Windows Verifying System Requirements Windows*1 Macintosh*4For users of Mac OS 9.0 to 9.2.2/X10.2.8/X10.3.9 Connecting the Machine with a USB Cable Windows Connecting the MachineDouble-click the Setup icon Setup in a Windows EnvironmentOpening the Software Selection Screen for ALL Software Insert the Software CD-ROM into your computers CD-ROM driveInstalling the Printer Driver / PC-FAX Driver Click the Printer Driver buttonIf the machine is connected to an IPv6-only network Click the Standard installation button Window confirming installation of the display fonts This completes the installationFollow the on-screen instructions Printer name windowRegular Maintenance MaintenanceDocument glass Scanning areaCleaning the Bypass Feed Roller Replacing the Toner Cartridges Copy modeOpen the front cover Pull the toner cartridge toward youClose the front cover Remove the toner collection container Replacing the Toner Collection ContainerPlug the hole in the toner collection Open the holders two on the left and right sides Replacing the Stamp CartridgeInstall a new stamp cartridge Push the stamp unit back Misfeed location Removing MisfeedsSupplies Storage of suppliesSupply of spare parts and consumables Machine specifications / copier specifications SpecificationsPower consumption Required power supplyDimensions WeightAmbient environment Continuous copying speedsReversing single feeder specifications MX-RP11 Exit tray unit right tray specificationsAcoustic noise emission measurement according to ISO7779 Page Factory default passwords To the Administrator of the MachineFactory default administrator password Factory default passwords Web pagesImportant safety instructions Information on Disposal for Users private households Information on DisposalInformation on Disposal for Business Users European UnionSharp Electronics Europe GmbH Trademark acknowledgmentsMX-M282N/MX-M362N/MX-M452N/MX-M502N Start Guide