Sharp MX-M282N Replacing the Toner Collection Container, Remove the toner collection container

Page 41

MAINTENANCE

REPLACING THE TONER COLLECTION CONTAINER

The toner collection container collects excess toner that is produced during printing. When the toner collection container becomes full, "Replace used toner container." will appear. Follow the procedure below to replace the toner collection container.

Open the front cover.

Remove the toner collection container.

(1) Tilt the toner collection container forward.

Grasp the corners of the toner collection container with both hands as shown and tilt it forward until it stops.

(2) Slowly lift the toner collection container up.

3Place the box on a flat surface.

Place a sheet of newspaper on the surface before placing the box.

Do not point the holes down as used toner will spill out.

4	Remove the provided cap from the side

of the toner collection container.

Grasp the end of the cap and pull forward.

Image 41

Contents MX-M362N MX-M452N MX-M502N Start GuideGREEN-AND-YELLOW Earth EMC this machine and peripheral devicesNeutral LiveSoftware Licence WarrantyFor the users of the fax function FAX interface cable and Line cableContents Power notes Symbols in this manualDo not damage or modify the power cord Do not insert or remove the power plug with wet handsDo not install in a location with moisture or dust Installation notesLocations exposed to direct sunlight Locations with ammonia gasLocations subject to vibration About consumablesNear a wall Do not use a flammable spray to clean the machine Handling precautionsDo not remove the machine casing Do not make any modifications to this machineLaser information Safety PrecautionsOperation Guide Convenient methods for using the Operation GuidePrinted manuals Start Guide Opening the Web pages Access the Web server in the machine toDownloading the Operation Guide Open the Web pagesChecking the IP Address Press the System Settings keySelect the all custom setting list in the touch panel Exterior Part Names and FunctionsPunch module USB connector a type Supports USB 2.0 Hi-SpeedSaddle stitch finisher Finisher large stackerInterior Automatic Document Feeder and Document Glass LAN connector When the fax expansion kit is installedUSB connector B type Supports USB 2.0 Hi-Speed Side and BackTouch panel JOB Status key Print mode indicators Image send indicatorsSystem Settings key Operation PanelPower key Main power indicatorPower Save key Numeric keysMain power indicator Power key Turning the Power on and OFFMain power switch Power key Using the document glass Using the automatic document feederPlacing Originals Place the originals face up with the edges aligned evenlyPlain paper, special media Useable PaperTypes of paper that can be used in each tray Plain paper that can be usedBypass tray and tray Trays 1 toLoading paper in a tray Loading Paper in a TrayNames of the trays Configure the tray settings in the touch panel Changing the tray settingsExample Loading an envelope Loading paper in other traysBypass tray Large capacity tray CD-ROMS and Software Before Installing the SoftwarePCL6 printer driver PS printer driver Sharpdesk/Network Scanner Utilities CD-ROM for Windows For users of Mac OS 9.0 to 9.2.2/X10.2.8/X10.3.9 Verifying System RequirementsWindows*1 Macintosh*4 Connecting the Machine with a USB Cable Windows Connecting the MachineDouble-click the Setup icon Setup in a Windows EnvironmentOpening the Software Selection Screen for ALL Software Insert the Software CD-ROM into your computers CD-ROM driveIf the machine is connected to an IPv6-only network Installing the Printer Driver / PC-FAX DriverClick the Printer Driver button Click the Standard installation button Window confirming installation of the display fonts This completes the installationFollow the on-screen instructions Printer name windowRegular Maintenance MaintenanceDocument glass Scanning areaCleaning the Bypass Feed Roller Replacing the Toner Cartridges Copy modeOpen the front cover Pull the toner cartridge toward youClose the front cover Remove the toner collection container Replacing the Toner Collection ContainerPlug the hole in the toner collection Open the holders two on the left and right sides Replacing the Stamp CartridgeInstall a new stamp cartridge Push the stamp unit back Misfeed location Removing MisfeedsSupply of spare parts and consumables SuppliesStorage of supplies Machine specifications / copier specifications SpecificationsPower consumption Required power supplyDimensions WeightAmbient environment Continuous copying speedsAcoustic noise emission measurement according to ISO7779 Reversing single feeder specifications MX-RP11Exit tray unit right tray specifications Page Factory default passwords To the Administrator of the MachineFactory default administrator password Factory default passwords Web pagesImportant safety instructions Information on Disposal for Users private households Information on DisposalInformation on Disposal for Business Users European UnionSharp Electronics Europe GmbH Trademark acknowledgmentsMX-M282N/MX-M362N/MX-M452N/MX-M502N Start Guide