Sharp MX-M450U, MX-M350N, MX-M450N, MX-M350U operation manual Manually Setting the Scanning Size

CHECKING THE SIZE OF A LOADED ORIGINAL

When a standard-size* original is placed, the original size is automatically detected (automatic original detection function) and displayed in the top half of the [ORIGINAL] key. Check the key to make sure that the original size has been correctly detected. :[AUTO] appears when the automatic original detection function is operating. :Displays the original size.

If a non-standard size original is placed or if you wish to change the scanning size, follow the steps below to manually set the original scanning size.

STANDARD

RESOLUTION

AUTO A4 ORIGINAL

NOTE

*Standard sizes that can be detected are as follows:

A5, B5, B5R, A4, A4R, B4, A3, 5-1/2"x8-1/2", 8-1/2"x11", 8-1/2"x11"R, 8-1/2"x14", 11"x17". If a non-standard size original is loaded (including special sizes), the closest standard size may be displayed, or the original size may not appear at all.

MANUALLY SETTING THE SCANNING SIZE

If you load an original that is not a standard size (such as an INCH size), or if the size is not detected correctly, you must touch the [ORIGINAL] key and set the original size manually. Perform the following steps after loading the document in the automatic document feeder or on the document glass.

1 Touch the [ORIGINAL] key.

	If the address book screen
	appears,	touch	the
STANDARD
	[CONDITION SETTINGS]
RESOLUTION
	key to	display	the
	condition	settings screen
AUTO A4
	(page 1-5).
ORIGINAL

2 Touch the key under [SCAN SIZE].

		SPEAKER
SCAN SIZE		SEND SIZE
AUTO A4	100%	AUTO
2-SIDED	2-SIDED
BOOKLET	TABLET

If you placed a non-standard size original on the document holder or on the document glass, touch the [SIZE INPUT] tab and then enter the width (X) and length

(Y) of the original with the keys.

X (width)

is

initially

X

OK

selected. Enter

X

and

A

Y

then touch

the

Y

( )

mm(64

432)

key to enter Y. A width of

X

420

64 to 432 mm (2-1/2 to 17

mm(64

297)

Y

297

inch) can be entered in X,

and a length of 64 to 297

STANDARD SIZE

SIZE INPUT

mm (2-1/2 to 11-5/8 inch) can be entered in Y.

If you

frequently send

documents that

are

the

same

non-standard size, you can store the dimensions as explained in "STORING, DELETING, AND USING ORIGINAL SIZES" on the following page. This will allow you to omit entry of X and Y each time you send that size of document.

3 Touch the desired original size key.

4 Touch the outer [OK] key.

Touch the [OK] key to return to the screen of step 2.

					SPEAKER				RESEND
		81/2X11								OK
				A5		A4
	AUTO									AB
				A5R		A4R
	MANUAL									INCH
				B5		B4
STOM				B5R		A3		LONG SIZE
ZE
			STANDARD SIZE				SIZE INPUT

[AUTO] is no longer highlighted. [MANUAL] and the original size key

you touched are highlighted.

If you placed a long original, touch the LONG SIZE key.

5 Touch the outer [OK] key.
SPEAKER	RESEND
SEND SIZE	OK
AUTO

If you wish to select an INCH size, touch the [AB/INCH] key and then touch the desired original size key.

-SIDED

	SPEAKER			RESEND
					OK
51/2X81/2		81/2 X13
51/2X81/2 R		81/2X14			AB
					INCH
81/2X11		11X17
81/2 X11R				LONG SIZE
STANDARD SIZE
			SIZE INPUT

[INCH] is highlighted and INCH size keys are displayed. To return to the inch palette, touch the [AB/INCH] key once again.

6 The selected size appears in the top half of the [ORIGINAL] key.

STANDARD

RESOLUTION

81/2X11

ORIGINAL

1-8