Sharp AL-2020 TD Cartridge Replacement, Gently pull the TD cartridge out, Lock release button

Page 59

7

MAINTENANCE

 

This chapter describes how to replace the TD cartridge and drum cartridge and how to clean the unit.

Be sure to use only genuine SHARP parts and supplies.

TD CARTRIDGE REPLACEMENT

The TD cartridge replacement required ( ) indicator will light up when toner is needed. For more information on purchasing the TD cartridge, see "ABOUT SUPPLIES AND OPTIONS" (p.72). If copying is continued while the indicator is lit, copies will gradually become lighter until the unit stops and the indicator begins blinking. Replace the old TD cartridge by following the procedure below.

• After the unit stops, it may be possible to make a few more copies by taking the TD cartridge out of the unit, shaking it horizontally, then reinstalling it. If copying is not possible after this operation, replace the TD cartridge.

During long copy run of a dark original, the TD cartridge replacement

required ( ) indicator may light up, the start () indicator blink, and the unit stops, even though toner is left. The unit will feed toner up

to 2 minutes and then the start () indicator will light up. Press the start () key to restart copying.

1

2

Open the multi-bypass tray, side cover, and front cover, in that order.

To open the multi-bypass tray, see "The multi-bypass tray" (p.17). To open the side cover and front cover, see "INSTALLING THE TD CARTRIDGE" (p.10).

Gently pull the TD cartridge out

Lock release button

7

while pressing the lock release

 

button.

Dispose of the old TD cartridge in accordance with local regulations.

3 Install a new TD cartridge. To install the new cartridge, see "INSTALLING THE TD CARTRIDGE" (p.10).

57

Image 59
Contents AL-2020 AL-2040 Bank drafts Be sure to allow the required space around Important points when selecting an installation siteDo not install your unit in areas that are Supply and ConsumablesLaser information Software LicenseTrademark acknowledgements Contents Conventions used in this manual and online manual Using the ManualsOnline manual SPF AL-2040 Part NamesOperation Panel Original to copy key and indicatorsSetup Procedure Setting UP the UnitPreparing the Unit for Installation Checking Packed Components and AccessoriesLockUnlock AL-2020 AL-2040 Release the scan head locking switchGently insert the TD cartridge Installing the TD CartridgePage Connecting the Power Cord About the scan head Power off methodsInitial settings of operation panel Paper Type of paper Type of media Size Weight FeedingLoading the Paper Tray Gently push the paper tray back into the unit Open the multi-bypass tray and extend the tray Multi-bypass trayPaper must be fed narrow side into the feed slot Press the tray select key to select the multi-bypass trayButton Manager SoftwareMFP driver Sharpdesk2000/XP/Vista Before InstallationInstallation environment and usable software Hardware and software requirementsUsing the machine with a USB connection Installing the SoftwareClick the MFP Driver button AL-2020 AL-2040 Select Connected to thisComputer and click This completes the installation of the software When installing is finished, click the Close buttonInsert the LAN cable into the LAN connector on the machine Connecting a USB cableUsing the machine as a network printer AL-2040 only Set the IP Address Click the Printer Driver button Enter the IP address, subnet mask, and default gatewayLPR TCP/IP direct printing Page Using the machine as a shared printer Click the Printer Driver button You will return to the window of . Click the Close button Sharing the printer using windows networking AL-2040This completes the installation of the software Power save indicator Indicators on the Operation PanelStart indicator Online indicatorClick Printing Preferences button in the General tab Using the Printer ModeOpening the printer driver from the start menu How to print Setting up the Button Manager Windows XP/Vista Using the Scanner ModeUsing the Button Manager Properties screen, click Events tab Windows 98/Me/2000Select Sharp AL-xxxx, and click the Properties button Scan Button Destination Setting Dialog Box Flow of the Button Manager setting Scanner Event Application Application launched Number Using the Scan key to begin scanningPress the Scan key Press the right copy quantityPress the start Key Opening the scanner driver and scanning from your computerScan is started Click Finish in the screen that appears Scanning with the Scanner and Camera Wizard in Windows XPSelect a name, format, and folder for the scanned image HOW to USE the Online Manual Start copying Select the copy settingsCopy Flow Place the originalAbout interrupt copying Original PlacementUsing the document glass Document feeder tray Using the SPF AL-2040SET the Copy Quantity Exposure ADJUSTMENT/PHOTO CopyingExposure adjustment Photo modeAutomatic exposure adjustment Press the tray select key REDUCTION/ENLARGEMENT/ZOOMSelecting the Paper Tray Set the reduction/enlargement ratioTWO Sided Copying Special FunctionsUsing the document glass Press the start key When copying in a one-sided to two-sided modeDescription of Other Special Functions Toner Save ModeUser Programs Setting the user programsExample Total number of copies is 1,234 Press the light key to return to the normal copy modeProgram Mode Parameters Displaying Total Number of CopiesLock release button TD Cartridge ReplacementGently pull the TD cartridge out While pressing the lock release ButtonOld drum cartridge Accordance with local regulations Drum Cartridge ReplacementGently pull the cartridge out. Dispose Page Document glass and the back side of the SPF Cleaning the UnitCabinet Transfer charger Troubleshooting Troubleshooting the UnitIndication Cause and remedy Status IndicatorsMisfeed Removal Misfeed in the paper feed area Lever Misfeed in the fusing areaLower the fusing unit release Rotate the roller rotating Knob in the direction Lower the fusing unit release leverMisfeed in the transport area Open the front coverMisfeed in the SPF AL-2040 Press the copy ratio display % key Appendix SpecificationsAL-2020 AL-2040 Bit depth USB interface cable About Supplies and OptionsSupply list Interface cableStore the supplies in a location that is Moving and Storing the UnitMoving instructions Proper storageMaterial Safety Data Sheet Hazards Identification Exposure Controls / Personal Protection Ecological Information Msds No. F-31231 2/4 Toner Date Revised Mar Date Issued Sep Msds No. F-31231 Index Drum replacement required IndicatorMFP driver Index by Purpose Other Countries outside the EU Class Laser Product Laser Klasse Sharp Manufacturing France S.A AL-2020/AL-2040v1
Related manuals
Manual 42 pages 53.03 Kb

AL-2040, AL-2020 specifications

The Sharp AL-2020 and AL-2040 are compact, multifunctional black-and-white copiers designed for small to mid-sized office environments. Known for their versatility and reliability, these models have become popular choices for businesses looking to enhance efficiency and output quality.

One of the standout features of both the AL-2020 and AL-2040 is their impressive printing and copying speed. The AL-2020 offers a speed of up to 20 pages per minute, while the AL-2040 enhances this capability with a speed of up to 40 pages per minute, catering to higher volume environments. This efficiency helps reduce wait times, allowing users to focus on other important tasks.

Both models are equipped with a user-friendly control panel that makes navigation easy. The LCD display provides clear visibility of settings, making it simple for users to adjust configurations and monitor the copier's status. Additionally, the AL-2040 features advanced finishing options, allowing users to execute tasks such as double-sided printing and stapling with ease, enhancing its utility within any office setting.

The Sharp AL-2020 and AL-2040 also incorporate advanced technologies that ensure outstanding print quality. With a resolution of 600 x 600 dpi, users can expect sharp text and detailed graphics, making these machines suitable for professional documents, presentations, and reports.

Another significant characteristic of these copiers is their environmental consideration. Both models feature low-energy consumption during operation and standby modes, contributing to a greener office environment. Sharp has also integrated long-life consumables into these models, which not only reduce waste but also lower the total cost of ownership.

Moreover, the AL-2040 comes with network printing capabilities, allowing multiple users within a network to share the device seamlessly. This feature is particularly beneficial in collaborative office settings where shared resources are essential.

Lastly, ease of maintenance is a key characteristic of the Sharp AL-2020 and AL-2040. Designed for straightforward servicing, these copiers minimize downtime and ensure smooth operation, making them reliable partners for any business looking to streamline its document management processes. With competitive features and robust performance, the Sharp AL-2020 and AL-2040 stand out as reliable solutions for modern office needs.