Sharp PN-A601 Language, Power on Delay, Standby Mode, OFF if no Operation, HOT Plug Control

Page 24
MENU .

Menu Items

LANGUAGE

Sets the display language for the menu screen.

POWER ON DELAY

You can delay the screen display after the monitor is turned on. The period can be set up to 60 seconds in units of one second. When this function is activated, the power LED flashes (at approx. 1 second interval) in orange. This function is disabled when 0 is specified.

STANDBY MODE

When STANDARD is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed in standby mode.

When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the startup time from standby mode becomes longer.

If set to LOW POWER, certain RS-232C commands cannot be used in standby mode, and control via LAN will be disabled.

OFF IF NO OPERATION

Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit, RS-232C commands, or LAN for over 4 hours.

HOT PLUG CONTROL

Sets whether to use hot plug control for the PC/AV HDMI and PC/AV DVI-D input terminals.

RS-232C/LAN SELECT

Selects the method with which to control the monitor from the computer.

ID No. SET

Assigns ID numbers to monitors connected in a daisy chain (see page 33), using the RS-232 cables.

The numbers 1 to 255 are available for ID numbers.

If “0” is set, the system regards this as the state where no ID number is set.

AUTO ASSIGN ID No.

ID No. to be used will be automatically assigned when multiple monitors are connected with RS-232C.

Select ON, then press MENU .

Perform operations using the first monitor in the daisy chain.

BAUD RATE

Selects the communication speed used for RS-232C communication.

LAN SETUP

Configures the settings to control the monitor from the computer via LAN. (See page 44.)

AUTO ASSIGN FIXED IP ADDR.

Can be enabled when RS-232C/LAN SELECT is LAN and the DHCP CLIENT is OFF.

Set DHCP CLIENT to OFF for the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows. Fixed IP addresses are automatically allocated.

If the IP address is a duplicate with a network device other than a monitor, individually change the IP address.

OPTION DC OUT SETTING

Normally, leave this setting as OFF.

When using an optional part, if instruction appears, change the setting accordingly.

HDMI AUTO VIEW

When ON is selected, the screen size is adjusted automatically according to the screen size control signal included in the video signal input from the AV HDMI input terminal.

BRIGHTNESS SENSOR

When set to ON or ON: DISPLAY, the brightness will automatically change according to the lighting and surrounding brightness. If set to ON: DISPLAY, the effect will

be displayed with a .

When setting BRIGHT in SCHEDULE on the OPTION menu, set BRIGHTNESS SENSOR to OFF.

BRIGHTNESS SENSOR SETTING

Performs adjustments to the brightness sensor.

Set the surrounding brightness and the current screen luminance to AMBIENT BRIGHTNESS and SCREEN BRIGHTNESS.

Individually set WHEN LIGHT: and WHEN DARK:. Even if brighter or darker than the set AMBIENT BRIGHTNESS, the screen brightness will not change. CURRENT AMBIENT BRIGHTNESS is shown for reference.

CONTROL KIT SETTING

When the PN-ZR01 control kit (optional) is connected, select whether to use the remote control sensor and the brightness sensor on the remote control sensor box or the monitor. Individually set REMOTE CONTROL SENSOR and

BRIGHTNESS SENSOR.

EXTERNAL

Use the remote control sensor box.

INTERNAL

Use the monitor.

COPY SETTING VALUE

When the monitor has been connected to multiple monitors by RS-232C, the settings in the monitor can be copied to the monitor connected to the RS-232C output terminal and to the daisy chain of connected monitors that follows.

Selects the settings to copy with COPY SETTING VALUE TARGET.

“PICTURE” ONLY....

Copies the PICTURE menu settings.*

ALL

Copies all the settings.*

Select the ID No. of the monitor that you would like copy to with COPY TO ID No., then select COPY and press

If you select ALL, settings will be copied to all monitors. When you would like to confirm the ID No. that is set to the

monitor, select ID No. DISPLAY and press . The ID No. will be displayed on the screen.

*Certain setting details such as ANALOG GAIN, ANALOG OFFSET, and DISPLAY COLOR PATTERN cannot be copied.

LOGO SCREEN

Sets whether or not to display the logo screen.

E24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PN-A601 For Customers in U.K GREEN-AND-YELLOWBlue BrownRefer Servicing to Qualified Service Personnel Important InformationInformation on Disposal for Users private households Information on Disposal for Business UsersEuropean Union Other Countries outside the EUDear Sharp Customer Safety Precautions Use only the power cord supplied with the monitor Fan in this product has a limited lifetimeMounting Precautions Do not place the monitor on a device which generates heatContents Supplied ComponentsPart Names NFront viewNRear view 11 E Connecting Peripheral Equipment Connection when the PN-ZB01 optional is attachedConnecting Peripheral Equipment 13 EExample connection Audio1 input terminals Audio2 input terminalsWhen attaching the remote control sensor box to this monitor Preparing the Remote Control Unit Installing the batteriesRemote control operation range 15 EConnecting the Power Cord Binding CablesRemoving the Handles 17 ETurning Power On/Off Turning on the main powerTurning power on/off Disabling power on/off operationsBasic Operation 19 EMute MenuBasic Operation NSwitching the screen size Wide Zoom NormalDot by Dot Cut offMenu Items 21 EDisplaying the menu screen Menu item details Menu ItemsNSCREEN NPICTURENSETUP 23 EMenu Items NAUDIO Power on Delay Standby ModeLAN Setup Option DC OUT Setting25 E NOPTIONMenu Items NMULTI NPIP/PbyP27 E NDual screen displayMenu Items NEnlarge PIPMenu Items NZOOM2 Special Setting PowerNSCHEDULE DAY of the WeekAdjustments for PC screen display NAutomatic adjustmentNScreen display for adjustment 29 EALL Reset Adjustment LockAdjustment Lock Target Temperature AlertCommunication procedure Controlling the Monitor with a PC RS-232C31 E PC connectionWhen a command has been executed correctly When a command has not been executedWhen RS-232C/LAN Select is set to LAN If execution of the command is taking some time33 E NID numbersAdvanced operation Controlling the Monitor with a PC RS-232C NRepeater controlVOLM0020 ← OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←Setting of the Gamma user data 35 ERS-232C command table Power control/Input mode selectionHow to read the command table Command Command field See Direction37 E Controlling the Monitor with a PC RS-232C Screen menuControlling the Monitor with a PC RS-232C Picture menu Setup menu 39 EControlling the Monitor with a PC RS-232C Audio menu Controlling the Monitor with a PC RS-232C Option menu AsapAssa InputImage Position Epos setting 41 EControlling the Monitor with a PC RS-232C Multi menu Landscape orientation Portrait orientationInitialization/Functional Restriction Setting Function menu Controlling the Monitor with a PC RS-232C PIP/PbyP menuCommands for setting of the Gamma user data 43 EControlling the Monitor with a PC RS-232C Others Settings to connect to a LAN Controlling the Monitor with a PC LANTo set on the monitor Default Gateway 0.0 45 ETo set from a PC Controlling the Monitor with a PC LANControlling with a PC Basic operationStandby mode, Power on is the operation available 47 EInformation about this monitor appears User Name / Password DNS ServerAccept IP Address IP Address 1 to49 E Attach the log file to a TEMPERATURE/HARDWARE error e-mail Recipient E-MAIL AddressesCondition Confirmation51 E Troubleshooting Troubleshooting 53 ESpecifications NPN-A601 Product SpecificationsNPN-ZR01 optional Product Specifications NDimensional Drawings Specifications NPower managementNPOWER Limited See 55 ESpecifications NCompatible signal timing PC HdmiSpecifications NCompatible signal timing AV 57 ESpecifications NPC/AV DVI-D input terminal pins NPC D-sub input terminal pinsNPC/AV DVI-D output terminal pins NPC/AV Hdmi input terminal pins59 E PN-A601 Mu EN11J1

PN-A601, PNA601 specifications

The Sharp PNA601, also known as the PN-A601, is a remarkable touchscreen display that has garnered attention in various commercial and professional environments. Designed for versatility and reliability, this model serves as an ideal solution for digital signage, interactive presentations, or as part of a collaborative workspace.

One of the standout features of the Sharp PNA601 is its impressive 60-inch diagonal screen size, which is specifically designed to capture attention while delivering vivid imagery. The display employs advanced LCD technology to ensure sharp picture quality with accurate color reproduction. The Full HD resolution of 1920 x 1080 pixels guarantees that text and images are displayed with stunning clarity, making it suitable for presentations where detail is critical.

In addition to its visual capabilities, the Sharp PNA601 is equipped with a multi-touch functionality that supports multiple touch points. This feature enables several users to interact with the display simultaneously, fostering collaboration during meetings or group presentations. The touch response is smooth and intuitive, making navigation and interaction seamless, whether for professional use or educational purposes.

The device is built with a durable and robust design that allows it to perform consistently in demanding environments. Its anti-glare glass surface minimizes reflections, ensuring that images remain visible in various lighting conditions. This durability extends to the display's long operational life, making it a cost-effective investment for businesses.

Connectivity options on the Sharp PNA601 are abundant, with multiple HDMI, VGA, and USB ports available. This variety ensures that the display can be easily connected to a range of devices, from laptops to media players, enhancing its usability in different settings. Additionally, the display supports various media formats, allowing users to showcase dynamic content with ease.

In terms of installation, the Sharp PNA601 offers flexibility with options for wall mounting or free-standing setups. This adaptability makes it suitable for different environments, whether in retail locations, conference rooms, or educational institutions.

Moreover, the Sharp PNA601 is energy-efficient, adhering to modern standards for sustainable technology. Its low power consumption while maintaining high performance showcases the manufacturer’s commitment to eco-friendly practices.

In conclusion, the Sharp PNA601/PN-A601 is a sophisticated touchscreen display that combines cutting-edge technology with practical features, making it an exceptional choice for a variety of applications. Its stunning visual capabilities, robust design, and user-friendly interface provide an unparalleled experience for anyone looking to enhance their digital presentations or interactive signage.
Top Page Image Contents