Runco VX-22I operation manual VX-22i Rear Panel

Page 20

2.2

VX-22i Rear Panel

Figure 2-2shows the VX-22i rear panel.

16

15

14

13

HD3 (VGA / Y-Pb-Pr)

Pr)-Pb-Y / (VGA HD3

HD2 (BNC)

(BNC) HD2

.cover lamp the off pull to screw the Remove

Remove the screw to pull off the lamp cover.

WIRED REMOTE

REMOTE WIRED

Service port. Not for user access

HD1 (RCA)

(RCA) HD1

SERVICE PORT

AUTHORIZED

PERSONNEL ONLY

L

L

2	4	6	8	10	12
1	3	5	7	9	11

Figure 2-2. VX-22i Rear Panel

1.LAMP COVER

Remove this cover to access the lamp compartment.

2.VACUUM FLUORESCENT DISPLAY (VFD)

Can be used instead of the OSD. Displays currently-selected menu or – if no menu is selected – the current source, input resolution and aspect ratio.

If an error condition occurs, a message	Please check issue(s)
appears here indicating the cause:	Please check issue(s)
	Communication Error

3.RUN LED

–Lights blue to indicate that the projector is functioning normally.

–Flashes blue (one second on/one second off) to indicate an error condition.

–Flashes blue (one half-second on/one half-second off) for approximately 90 seconds after the system is turned off.

4.ISSUE LED

Lights red to indicate an error condition.

6	Runco VX-22i Installation/Operation Manual

Image 20

Contents VX-22i Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Operation Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents Xii List of Figures List of Figures Xiv Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-22i at a GlanceVX-22i Rear Panel VX-22i Rear PanelPower Input 100 to 240 VAC Connect the VX-22i to power here Left ButtonVX-22i Rear Connector Panel Service only For future useRS-232/485 Control Port Volt 750 mA Trigger OutputsHdmi I 1 / Hdmi II 2 Digital HD3 InputVX-22i Remote Control VX-22i Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox LetterboxInstallation Remote ControlIf installing a VX-22i/CineWide or VX-22i/CineWide Quick SetupStep Procedure For Details, Refer to Ambient Light Installation ConsiderationsInstallation Type Throw Range Throw Ratio Inches, with Lens Option 96x54-inchLens Lens Only Anamorphic Minimum MaximumCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsPage Installing the Optional CineWide Lens Mount Remove Installing the AutoScope Lens Motor VX-22i/CineWide withAutoScope VX-22i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connector Panel Access Connecting SourceConnections to VX-22i11. Digital DTV RGB or Component Video Connections HD1, HD2 12. Digital DTV RGB or Component Video Connections HD3 DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure 13. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs toExternal Equipment AutoScope Lens Motor RearConnecting an External IR Connecting to AC PowerReceiver to Rear PanelTurning on the Power Adjusting the Picture OrientationZoom Primary Lens AdjustmentsFocus Installing and Adjusting the CineWide Anamorphic Lens Assembly to Lens MotorCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Configure Lens Motor Adjust the AnamorphicAdjusting the Horizontal X Lens Position TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Using the On-Screen Menus OperationMemory Presets ServiceInput Source Aspect RatioAspect Ratio Main MenuInput Source Remote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsHdtv programs in their Native aspect ratioPicture PictureRemote Aspect Ratio Control Description Key Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationISF Day CalibrationCalibration ISF Night Gain/Offset Refer to ISF Night Display Color, above HD Format ServiceService ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Symptom Possible Causes SolutionPage If you are using a PC to communicate with Serial CommunicationsAspect Ratio Commands Command Description ResponseInput Selection Commands Command Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select buttonPage Specifications VX-22i SpecificationsSpecifications are subject to change without notice Home Theater Calibration SpecificationsIndustry-Standard Specifications VX-22i Dimensions VX-22i/CineWide with AutoScope DimensionsSupported Timings PAL-B/G Page Page Runco CL-810 Owner’s Operating Manual