Runco VX-22I operation manual Calibration ISF Night, ISF Day

Page 69

Use the Calibration menu to perform advanced picture quality adjustments. This menu should be used by ISF-certified technicians only.

You must enter a passcode to access the Calibration menu.

Note

To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the ISF Presets menu (see page 54) or use the corresponding buttons on the remote control.

ISF Night - Display Color: Use the Display Color settings to adjust the color balance at the projector output. These settings are saved independently for each input.

•Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red (Pr), green (Y) or blue (Pr), decrease the Gain for that color.

•Offset: Use the Offset controls in the White Balance sub-menu to correct color imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red (Pr), green (Y) or blue (Pr), decrease the Offset for that color.

•Gamma: “Gamma” determines how gray shades are displayed between minimum input (black) and maximum input (white) for all signals. A good gamma setting helps to optimize blacks and whites while ensuring smooth transitions for the “in-between” values utilized in other grays. Unlike “Brightness” and “Contrast” controls, the overall tone of your images can be lightened or darkened without changing the extremes and all images will be more vibrant while still showing good detail in dark areas.

In all but the most unusual situations, the appropriate “Color Temp” selection (see below) will produce accurate colors and a satisfying contrast level. However, it is sometimes necessary to adjust the red, blue and green gamma curves individually. To do this, select Gamma from the Display Color sub-menu and use the left- and right-arrow buttons to manipulate the on-screen slidebars.

•Lamp Power: Select Lamp Power from the Display Color menu to adjust the lamp output level. You can choose to run the lamp as bright as possible (300W; this is the default setting) or you can choose the lower (250W) setting. Generally, lower lamp output prolongs the life of the lamp, but decreases brightness.

•Color Temp: Select Color Temp from the Display Color menu to adjust the color temperature. The default setting is appropriate for most situations. Higher settings produce a “bluer” picture.

ISF Night - Input Image: The Input Image controls are similar to those in the Picture menu, but are accessible only by entering the Calibration menu passcode. This makes it possible to restore the picture quality settings to what they were when the projector was installed, simply by recalling the “ISF Night” preset.

Calibration

Calibration

ISF Night

Display Color

Input Image

Input Color

ISF Day

Display Color

Input Image

Input Color

Save ISF Settings

Output Shift

Splash Timer

OSD Position

Runco VX-22i Installation/Operation Manual

55

Page 68 Page 70
Image 69
Page 68 Page 70
Contents VX-22i Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Operation Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents Xii List of Figures List of Figures Xiv About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories VX-22i at a Glance Controls and FunctionsVX-22i Rear Panel VX-22i Rear PanelLeft Button Power Input 100 to 240 VAC Connect the VX-22i to power hereService only For future use VX-22i Rear Connector PanelRS-232/485 Control Port Volt 750 mA Trigger OutputsHD3 Input Hdmi I 1 / Hdmi II 2 DigitalVX-22i Remote Control VX-22i Remote ControlOn / OFF Picture Adjustment Buttons BRT BrightnessSource Selection Buttons VID S-VideoAspect Ratio Selection Buttons Memory Preset Buttons169 Lbox LetterboxRemote Control InstallationQuick Setup Step Procedure For Details, Refer toIf installing a VX-22i/CineWide or VX-22i/CineWide Installation Considerations Installation TypeAmbient Light 96x54-inch Throw Range Throw Ratio Inches, with Lens OptionLens Lens Only Anamorphic Minimum MaximumFloor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsOther Considerations Installing the Primary Projection LensPage Installing the Optional CineWide Lens Mount Installing the AutoScope Lens Motor VX-22i/CineWide with AutoScopeRemove VX-22i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connecting Source Connector Panel AccessConnections to VX-22i11. Digital DTV RGB or Component Video Connections HD1, HD2 DTV or Progressive Component YPbPr Source 12. Digital DTV RGB or Component Video Connections HD313. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See FigureConnection RS-232 ControllerTrigger Outputs to Connecting 12-voltExternal Equipment AutoScope Lens Motor RearConnecting to AC Power Connecting an External IRReceiver to Rear PanelAdjusting the Picture Orientation Turning on the PowerPrimary Lens Adjustments FocusZoom Assembly to Lens Motor Installing and Adjusting the CineWide Anamorphic LensCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjust the Anamorphic Configure Lens MotorAdjusting the Horizontal X Lens Position TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Operation Using the On-Screen MenusService Memory PresetsInput Source Aspect RatioMain Menu Input SourceAspect Ratio Select 169 to view 169 DVDs Remote Aspect Ratio Control Description Key 169Hdtv programs in their Native aspect ratioPicture Remote Aspect Ratio Control Description KeyPicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Lamp Replacement Maintenance and TroubleshootingSide Filter Access Panel Filter ReplacementSymptom Possible Causes Solution Troubleshooting TipsPage Serial Communications If you are using a PC to communicate withCommand Description Response Input Selection CommandsAspect Ratio Commands Menu Navigation Commands Command Description Response Image Preset CommandsPicture Adjust Commands Enter or Select buttonPage VX-22i Specifications SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsSpecifications are subject to change without notice VX-22i/CineWide with AutoScope Dimensions VX-22i DimensionsSupported Timings PAL-B/G Page Page Runco CL-810 Owner’s Operating Manual
Top Page Image Contents