Runco VX-22I operation manual Serial Communications, If you are using a PC to communicate with

Page 77

Serial Communications

To interface the VX-22i with a home theater automation/control system or a PC running terminal emulation software, connect it to your control system or PC as shown in Figure 3-15.Use a null-modem cable.

If you are using a PC to communicate with the VX-22i:

1.Start a terminal session on your PC using a terminal-emulation program, such as HyperTerminal.

2.Configure the PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to 19200, to match that of the VX-22i RS-232 port.

3.Press <Enter>. You should see a command prompt (>) in the terminal window.

4.Type a command from among those listed in Table 6-1and press <Enter>.

•Commands are in ASCII format and are not case-sensitive; on and ON are equivalent.

•For a command that takes no parameters, type the command followed by a carriage return; for example, to turn on the system, type ON<Enter>.

•For a command that takes a parameter, type the command, one or more spaces and the desired value followed by a carriage return; for example, to switch to the S-Video input, type SSRC 1<Enter>.

•When you enter a valid command, the VX-22i executes it. When you send an on/off, input selection, aspect ratio or image preset command, the VX-22i also responds with an acknowledgment on the command line. For example, when you issue the command SAR 2, the VX-22i responds with Letterbox on the command line.

•When you enter a misspelled or otherwise invalid command, the VX-22i ignores it and responds with Invalid Command on the command line.

•When you send a command followed by values outside the valid range for that command, the VX-22i ignores it and responds with Invalid Parameter on the command line.

•When the VX-22i receives an OFF command, it will not acknowledge or execute any commands for approximately 90 seconds afterwards. This is to prevent hot re-strikes of the lamp, which can damage it.

6.1

RS-232 Connection and Port Configuration

6.2

Serial Command Syntax

Runco VX-22i Installation/Operation Manual

63

Image 77

Contents VX-22i Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Operation Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents Xii List of Figures List of Figures Xiv About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories VX-22i at a Glance Controls and FunctionsVX-22i Rear Panel VX-22i Rear PanelLeft Button Power Input 100 to 240 VAC Connect the VX-22i to power hereService only For future use VX-22i Rear Connector PanelRS-232/485 Control Port Volt 750 mA Trigger OutputsHD3 Input Hdmi I 1 / Hdmi II 2 DigitalVX-22i Remote Control VX-22i Remote ControlOn / OFF Picture Adjustment Buttons BRT BrightnessSource Selection Buttons VID S-VideoAspect Ratio Selection Buttons Memory Preset Buttons169 Lbox LetterboxRemote Control InstallationIf installing a VX-22i/CineWide or VX-22i/CineWide Quick SetupStep Procedure For Details, Refer to Ambient Light Installation ConsiderationsInstallation Type 96x54-inch Throw Range Throw Ratio Inches, with Lens OptionLens Lens Only Anamorphic Minimum MaximumFloor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsOther Considerations Installing the Primary Projection LensPage Installing the Optional CineWide Lens Mount Remove Installing the AutoScope Lens Motor VX-22i/CineWide withAutoScope VX-22i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connecting Source Connector Panel AccessConnections to VX-22i11. Digital DTV RGB or Component Video Connections HD1, HD2 DTV or Progressive Component YPbPr Source 12. Digital DTV RGB or Component Video Connections HD313. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See FigureConnection RS-232 ControllerTrigger Outputs to Connecting 12-voltExternal Equipment AutoScope Lens Motor RearConnecting to AC Power Connecting an External IRReceiver to Rear PanelAdjusting the Picture Orientation Turning on the PowerZoom Primary Lens AdjustmentsFocus Assembly to Lens Motor Installing and Adjusting the CineWide Anamorphic LensCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjust the Anamorphic Configure Lens MotorAdjusting the Horizontal X Lens Position TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Operation Using the On-Screen MenusService Memory PresetsInput Source Aspect RatioAspect Ratio Main MenuInput Source Select 169 to view 169 DVDs Remote Aspect Ratio Control Description Key 169Hdtv programs in their Native aspect ratioPicture PictureRemote Aspect Ratio Control Description Key Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationISF Day CalibrationCalibration ISF Night Gain/Offset Refer to ISF Night Display Color, above HD Format ServiceService ISF Day/Night presets Lamp Replacement Maintenance and TroubleshootingSide Filter Access Panel Filter ReplacementSymptom Possible Causes Solution Troubleshooting TipsPage Serial Communications If you are using a PC to communicate withAspect Ratio Commands Command Description ResponseInput Selection Commands Menu Navigation Commands Command Description Response Image Preset CommandsPicture Adjust Commands Enter or Select buttonPage VX-22i Specifications SpecificationsSpecifications are subject to change without notice Home Theater Calibration SpecificationsIndustry-Standard Specifications VX-22i/CineWide with AutoScope Dimensions VX-22i DimensionsSupported Timings PAL-B/G Page Page Runco CL-810 Owner’s Operating Manual