Runco VX-22I operation manual Service, HD Format

Page 71

Use the Service menu to access advanced projector configuration settings. This menu should be used by ISF-certified technicians only.

You must enter a passcode to access the Service menu.

Note

Test Video: Select Test Video from the Service Menu to access the internal test patterns

on the VX-22i. Four patterns are available: Horizontal Ramp, Vertical Ramp, Color Bars 1 (solid bars) and Color Bars 2 (SMPTE “checkerboard” pattern).

Press MENU to exit test pattern mode.

Tip

You can also use the PATTERN button on the projector rear panel

to enter and exit test pattern mode.

Service

Service

Test Video

Display Device

HD Format

Triggers

Miscellaneous

System Reset

Restore Saved Settings

Display Device: The options in the Display Device menu allow you to change the picture orientation and perform lens adjustments.

•Installation: Select Installation from the Display Device menu to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

•Lens: Select Lens from the Display Device menu to access the motorized lens controls. Refer to Primary Lens Adjustments on page 37.

•Lamp Info: Select Lamp Info from the Display Device menu to obtain information

about the currently-installed lamp: its serial number, number of “strikes” (attempts to ignite) and number of hours in use.

•Diagnostic: Select Diagnostic from the Display Device menu, then select Red, Green, Blue, Yellow, Cyan or Magenta to display only that color (simulating a filter of that color). This can be useful for calibration or measurement purposes.

To restore the normal picture (all colors), select White.

HD Format: Select HD Format from the Service menu to choose the default color space for the source signals on the HD1, HD2 and HD3 inputs. Select COMP (component) or RGB. The DHD Controller assumes this color space when you “direct-select” an HD input using the left-arrow and right-arrow ( or ) buttons on the projector rear panel or DHD Controller front panel, or the HD1, HD2 or HD3 buttons on the remote control unit.

You can override this setting by using the OSD to select an HD input (refer to Input Source on page 47). For example, if you select COMP for HD2 here and the input signal changes to RGB, select “RGB BNC” from the Input Source menu to enable the VX-22i to properly display that signal.

Note

When you change the default color space for an HD input, it takes

effect the next time you select that input (not immediately).

HD Format

HD1 7 COMP … RGB

HD2

7 COMP

… RGB

HD3

… COMP

7 RGB

Runco VX-22i Installation/Operation Manual

57

Page 70 Page 72
Image 71
Page 70 Page 72
Contents VX-22i Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Operation Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents Xii List of Figures List of Figures Xiv About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories VX-22i at a Glance Controls and FunctionsVX-22i Rear Panel VX-22i Rear PanelLeft Button Power Input 100 to 240 VAC Connect the VX-22i to power hereVolt 750 mA Trigger Outputs VX-22i Rear Connector PanelService only For future use RS-232/485 Control PortHD3 Input Hdmi I 1 / Hdmi II 2 DigitalVX-22i Remote Control VX-22i Remote ControlVID S-Video Picture Adjustment Buttons BRT BrightnessOn / OFF Source Selection ButtonsLbox Letterbox Memory Preset ButtonsAspect Ratio Selection Buttons 169Remote Control InstallationIf installing a VX-22i/CineWide or VX-22i/CineWide Quick SetupStep Procedure For Details, Refer to Ambient Light Installation ConsiderationsInstallation Type Lens Only Anamorphic Minimum Maximum Throw Range Throw Ratio Inches, with Lens Option96x54-inch LensPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example only Folded Optics Folded OpticsOther Considerations Installing the Primary Projection LensPage Installing the Optional CineWide Lens Mount Remove Installing the AutoScope Lens Motor VX-22i/CineWide withAutoScope VX-22i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting VX-22i Connector Panel AccessConnecting Source Connections to11. Digital DTV RGB or Component Video Connections HD1, HD2 DTV or Progressive Component YPbPr Source 12. Digital DTV RGB or Component Video Connections HD313. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See FigureConnection RS-232 ControllerAutoScope Lens Motor Rear Connecting 12-voltTrigger Outputs to External EquipmentRear Panel Connecting an External IRConnecting to AC Power Receiver toAdjusting the Picture Orientation Turning on the PowerZoom Primary Lens AdjustmentsFocus With AutoScope or Base Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor Carriage Plate CineWide19. Attaching the Anamorphic Lens to the Lens Adapter Ring Trigger Configure Lens MotorAdjust the Anamorphic Adjusting the Horizontal X Lens PositionPage Anamorphic Lens Top View Adjusting the Geometry Page Operation Using the On-Screen MenusAspect Ratio Memory PresetsService Input SourceAspect Ratio Main MenuInput Source Native aspect ratio Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirPicture PictureRemote Aspect Ratio Control Description Key Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation Memory PresetsMemory Presets InformationISF Day CalibrationCalibration ISF Night Gain/Offset Refer to ISF Night Display Color, above HD Format ServiceService ISF Day/Night presets Lamp Replacement Maintenance and TroubleshootingSide Filter Access Panel Filter ReplacementSymptom Possible Causes Solution Troubleshooting TipsPage Serial Communications If you are using a PC to communicate withAspect Ratio Commands Command Description ResponseInput Selection Commands Enter or Select button Command Description Response Image Preset CommandsMenu Navigation Commands Picture Adjust CommandsPage VX-22i Specifications SpecificationsSpecifications are subject to change without notice Home Theater Calibration SpecificationsIndustry-Standard Specifications VX-22i/CineWide with AutoScope Dimensions VX-22i DimensionsSupported Timings PAL-B/G Page Page Runco CL-810 Owner’s Operating Manual
Top Page Image Contents