Runco VX-22I operation manual Configure Lens Motor, Trigger, Adjust the Anamorphic

Page 54

Configure Lens Motor

CineWide with AutoScope maintains constant image height independent of the aspect

Trigger

ratio, while using the full display resolution of the projector. It accomplishes this by moving

 

the anamorphic lens in front of the primary lens when widescreen material is being viewed.

 

When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens

 

moves out of the light path.

 

To configure the lens motor trigger on the VX-22i for proper AutoScope operation:

 

1.

Project a 2.35:1 aspect ratio test pattern or other image on the screen.

 

2.

Press MENU on the remote control and enter the Service menu passcode.

 

3.

Select Service from the Main menu.

 

4.

Select Triggers from the Service menu.

 

5.

Assign the trigger output to which the lens motor is connected to the Cinema and

 

 

Virtual Cinema aspect ratios. This enables the lens motor to move the anamorphic

 

 

lens into position (in front of the primary lens) when either aspect ratio is selected.

 

6.

To save the trigger settings, press repeatedly to highlight “Save.” Then, press

 

 

ENTER.

 

7.

Select the Cinema aspect ratio to move the anamorphic lens into position, if it isn’t

 

 

already. To do this, press CINEMA on the VX-22i remote control (Figure 2-4), or

 

 

press or repeatedly with no menus visible on-screen.

Adjust the Anamorphic

Adjusting the Horizontal (X) Lens Position:

Lens

1.

Project a white field on the screen.

 

 

2.

Loosen the Yaw/X-Adjustment Levers underneath the lens.

 

3.

Slowly move the anamorphic lens into place so that there are no shadows on either

 

 

side of the screen:

Too Far Left

Correct position

Too Far Right

4.When the horizontal position is properly set, tighten the Yaw/X-Adjustment Levers to secure the lens in place.

40

Runco VX-22i Installation/Operation Manual

Image 54
Contents VX-22i Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Operation Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents Xii List of Figures List of Figures Xiv Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-22i at a GlanceVX-22i Rear Panel VX-22i Rear PanelPower Input 100 to 240 VAC Connect the VX-22i to power here Left ButtonRS-232/485 Control Port VX-22i Rear Connector PanelService only For future use Volt 750 mA Trigger OutputsHdmi I 1 / Hdmi II 2 Digital HD3 InputVX-22i Remote Control VX-22i Remote ControlSource Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox LetterboxInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toIf installing a VX-22i/CineWide or VX-22i/CineWide Installation Considerations Installation TypeAmbient Light Lens Throw Range Throw Ratio Inches, with Lens Option96x54-inch Lens Only Anamorphic Minimum MaximumVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsPage Installing the Optional CineWide Lens Mount Installing the AutoScope Lens Motor VX-22i/CineWide with AutoScopeRemove VX-22i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connections to Connector Panel AccessConnecting Source VX-22i11. Digital DTV RGB or Component Video Connections HD1, HD2 12. Digital DTV RGB or Component Video Connections HD3 DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure 13. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller ConnectionExternal Equipment Connecting 12-voltTrigger Outputs to AutoScope Lens Motor RearReceiver to Connecting an External IRConnecting to AC Power Rear PanelTurning on the Power Adjusting the Picture OrientationPrimary Lens Adjustments FocusZoom Carriage Plate CineWide Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Configure Lens MotorAdjust the Anamorphic TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Using the On-Screen Menus OperationInput Source Memory PresetsService Aspect RatioMain Menu Input SourceAspect Ratio Hdtv programs in their Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Native aspect ratioPicture Remote Aspect Ratio Control Description KeyPicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation Memory PresetsMemory Presets InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Symptom Possible Causes SolutionPage If you are using a PC to communicate with Serial CommunicationsCommand Description Response Input Selection CommandsAspect Ratio Commands Picture Adjust Commands Command Description Response Image Preset CommandsMenu Navigation Commands Enter or Select buttonPage Specifications VX-22i SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsSpecifications are subject to change without notice VX-22i Dimensions VX-22i/CineWide with AutoScope DimensionsSupported Timings PAL-B/G Page Page Runco CL-810 Owner’s Operating Manual