Runco VX-22I VX-22i Rear Connector Panel, Service only For future use, RS-232/485 Control Port

Page 22

2.3

VX-22i Rear Connector Panel

Figure 2-3shows the rear connector panel on the VX-22i, and the paragraphs that follow describe them.

10	9	8	7	6	5
		HD3 (VGA / Y-Pb-Pr)
		Pr)-Pb-Y / (VGA HD3

	HD1 (RCA)
HD2 (BNC)	(RCA) HD1
(BNC) HD2

4	3
WIRED REMOTE
REMOTE WIRED

Service port. Not for user access

12

Figure 2-3. Rear Connector Panel

1.HD2 INPUT

Five BNCs for connecting either RGB or component high-definition sources (up to 1080p). The VX-22i automatically detects the input signal resolution.

2.HD1 INPUT

Five RCA-type connectors for either RGB or component high-definition sources (up to 1080p). The VX-22i automatically detects the input signal resolution.

For best results, do not run your DVD player in progressive mode.

Tip

3.SERVICE ONLY For future use.

4.WIRED REMOTE

Wired input from an external remote control or infrared receiver. It is a 3.5-mm, mini phono jack, wired as follows:

Ring = +5V

Tip = IR Input (TTL level) Sleeve = Ground

When an external remote control or infrared receiver is connected

Note to the wired IR input, the IR sensor on the front of the VX-22i is disabled.

5.RS-232/485 CONTROL PORT

A male, 9-pin D-sub connector for interfacing with a PC or home theater automation/control system. (Currently, only RS-232 interface is supported.)

6.12-VOLT (750 mA) TRIGGER OUTPUTS

Connection for up to three (3), 12-volt trigger-controlled devices. These can be retractable screens, screen masks or the Runco CineWide with AutoScope system.

8	Runco VX-22i Installation/Operation Manual

Image 22

Contents VX-22i Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Operation Specifications Maintenance and TroubleshootingSerial Communications Table of Contents Xii List of Figures List of Figures Xiv Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-22i at a GlanceVX-22i Rear Panel VX-22i Rear PanelPower Input 100 to 240 VAC Connect the VX-22i to power here Left ButtonRS-232/485 Control Port VX-22i Rear Connector PanelService only For future use Volt 750 mA Trigger OutputsHdmi I 1 / Hdmi II 2 Digital HD3 InputVX-22i Remote Control VX-22i Remote ControlSource Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox LetterboxInstallation Remote ControlStep Procedure For Details, Refer to Quick SetupIf installing a VX-22i/CineWide or VX-22i/CineWide Installation Type Installation ConsiderationsAmbient Light Lens Throw Range Throw Ratio Inches, with Lens Option96x54-inch Lens Only Anamorphic Minimum MaximumVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsPage Installing the Optional CineWide Lens Mount AutoScope Installing the AutoScope Lens Motor VX-22i/CineWide withRemove VX-22i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connections to Connector Panel AccessConnecting Source VX-22i11. Digital DTV RGB or Component Video Connections HD1, HD2 12. Digital DTV RGB or Component Video Connections HD3 DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure 13. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller ConnectionExternal Equipment Connecting 12-voltTrigger Outputs to AutoScope Lens Motor RearReceiver to Connecting an External IRConnecting to AC Power Rear PanelTurning on the Power Adjusting the Picture OrientationFocus Primary Lens AdjustmentsZoom Carriage Plate CineWide Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Configure Lens MotorAdjust the Anamorphic TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Using the On-Screen Menus OperationInput Source Memory PresetsService Aspect RatioInput Source Main MenuAspect Ratio Hdtv programs in their Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Native aspect ratioRemote Aspect Ratio Control Description Key PicturePicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation Memory PresetsMemory Presets InformationCalibration ISF Night CalibrationISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Symptom Possible Causes SolutionPage If you are using a PC to communicate with Serial CommunicationsInput Selection Commands Command Description ResponseAspect Ratio Commands Picture Adjust Commands Command Description Response Image Preset CommandsMenu Navigation Commands Enter or Select buttonPage Specifications VX-22i SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsSpecifications are subject to change without notice VX-22i Dimensions VX-22i/CineWide with AutoScope DimensionsSupported Timings PAL-B/G Page Page Runco CL-810 Owner’s Operating Manual