Runco VX-22I operation manual Maintenance and Troubleshooting, Lamp Replacement

Page 73

5. Maintenance and Troubleshooting

The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. When you replace a lamp, you should replace the filters as well.

For lamp or filter replacement, please contact your nearest Runco authorized service center or Runco dealer. Do not attempt to replace the lamp yourself!

WARNING	The VX-22i lamp is under high pressure. Handle it with great care at
	all times. Lamps may explode if dropped or mishandled.

Never attempt to disassemble the lamp casing or dispose of the lamp casing in any manner other than by returning it to your Runco dealer.

If the lamp breaks, leave the area immediately and stay away for at least 30 minutes. Ventilate the room to allow the mercury vapor to disperse.

If you inhale the mercury vapor, see a physician immediately.

5.1

Lamp Replacement

1.Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement.

2.Loosen and remove the rear Lamp Cover screw.

3.Slide the Lamp Cover in the direction of the arrow to remove it.

4.Loosen the two, captive lamp assembly

mounting screws using a coin or a large, flat-blade screwdriver.

5.Grasp the lamp assembly handle and pull gently, removing the lamp module from the projector housing.

Runco VX-22i Installation/Operation Manual

59

Image 73

Contents VX-22i Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Operation Specifications Maintenance and TroubleshootingSerial Communications Table of Contents Xii List of Figures List of Figures Xiv About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories VX-22i at a Glance Controls and FunctionsVX-22i Rear Panel VX-22i Rear PanelLeft Button Power Input 100 to 240 VAC Connect the VX-22i to power hereService only For future use VX-22i Rear Connector PanelRS-232/485 Control Port Volt 750 mA Trigger OutputsHD3 Input Hdmi I 1 / Hdmi II 2 DigitalVX-22i Remote Control VX-22i Remote ControlOn / OFF Picture Adjustment Buttons BRT BrightnessSource Selection Buttons VID S-VideoAspect Ratio Selection Buttons Memory Preset Buttons169 Lbox LetterboxRemote Control InstallationStep Procedure For Details, Refer to Quick SetupIf installing a VX-22i/CineWide or VX-22i/CineWide Installation Type Installation ConsiderationsAmbient Light 96x54-inch Throw Range Throw Ratio Inches, with Lens OptionLens Lens Only Anamorphic Minimum MaximumFloor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsOther Considerations Installing the Primary Projection LensPage Installing the Optional CineWide Lens Mount AutoScope Installing the AutoScope Lens Motor VX-22i/CineWide withRemove VX-22i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connecting Source Connector Panel AccessConnections to VX-22i11. Digital DTV RGB or Component Video Connections HD1, HD2 DTV or Progressive Component YPbPr Source 12. Digital DTV RGB or Component Video Connections HD313. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See FigureConnection RS-232 ControllerTrigger Outputs to Connecting 12-voltExternal Equipment AutoScope Lens Motor RearConnecting to AC Power Connecting an External IRReceiver to Rear PanelAdjusting the Picture Orientation Turning on the PowerFocus Primary Lens AdjustmentsZoom Assembly to Lens Motor Installing and Adjusting the CineWide Anamorphic LensCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjust the Anamorphic Configure Lens MotorAdjusting the Horizontal X Lens Position TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Operation Using the On-Screen MenusService Memory PresetsInput Source Aspect RatioInput Source Main MenuAspect Ratio Select 169 to view 169 DVDs Remote Aspect Ratio Control Description Key 169Hdtv programs in their Native aspect ratioRemote Aspect Ratio Control Description Key PicturePicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationCalibration ISF Night CalibrationISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Lamp Replacement Maintenance and TroubleshootingSide Filter Access Panel Filter ReplacementSymptom Possible Causes Solution Troubleshooting TipsPage Serial Communications If you are using a PC to communicate withInput Selection Commands Command Description ResponseAspect Ratio Commands Menu Navigation Commands Command Description Response Image Preset CommandsPicture Adjust Commands Enter or Select buttonPage VX-22i Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsSpecifications are subject to change without notice VX-22i/CineWide with AutoScope Dimensions VX-22i DimensionsSupported Timings PAL-B/G Page Page Runco CL-810 Owner’s Operating Manual