Runco VX-22I operation manual Installing the Optional CineWide Lens Mount

Page 36

3.5

Installing the Optional CineWide Lens Mount

Make sure to route the wire harness in its original position and away Caution from the moving lens stages and Motor Assembly, to prevent

unexpected disconnection or lens damage.

7.Lock the lens in place by turning the Lens Locking Nut (to the left of the lens)

180 degrees counter-clockwise. (Use a 6.0mm hex wrench.)

8.Replace the Lens Cavity Front Cover.

9.Reattach the Projector Front Jewelry by sliding the top down onto the two retaining dowels. Tighten the Phillips screw at the top of the projector to secure it.

10.Remove the Front Lens Cap.

If you are installing a standard (non-CineWide) VX-22i, skip this step and proceed with Mounting the VX-22i(page 27).

If you are installing a VX-22i/CineWide, proceed with Installing the Fixed CineWide Base Plate (VX-22i/CineWide)(page 26).

If you are installing a VX-22i/CineWide with AutoScope, proceed as follows to install the AutoScope lens motor.

1. Do not install the CineWide lens yet, only the fixed CineWide

Note base plate or AutoScope lens motor. You will install the CineWide lens after you install the projector and adjust the primary lens.

2.Some components shipped with your projector may differ slightly from what is shown in these instructions.

22	Runco VX-22i Installation/Operation Manual

Image 36

Contents VX-22i Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Operation Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents Xii List of Figures List of Figures Xiv Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-22i at a GlanceVX-22i Rear Panel VX-22i Rear PanelPower Input 100 to 240 VAC Connect the VX-22i to power here Left ButtonVX-22i Rear Connector Panel Service only For future useRS-232/485 Control Port Volt 750 mA Trigger OutputsHdmi I 1 / Hdmi II 2 Digital HD3 InputVX-22i Remote Control VX-22i Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox LetterboxInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toIf installing a VX-22i/CineWide or VX-22i/CineWide Installation Considerations Installation TypeAmbient Light Throw Range Throw Ratio Inches, with Lens Option 96x54-inchLens Lens Only Anamorphic Minimum MaximumCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsPage Installing the Optional CineWide Lens Mount Installing the AutoScope Lens Motor VX-22i/CineWide with AutoScopeRemove VX-22i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connector Panel Access Connecting SourceConnections to VX-22i11. Digital DTV RGB or Component Video Connections HD1, HD2 12. Digital DTV RGB or Component Video Connections HD3 DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure 13. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs toExternal Equipment AutoScope Lens Motor RearConnecting an External IR Connecting to AC PowerReceiver to Rear PanelTurning on the Power Adjusting the Picture OrientationPrimary Lens Adjustments FocusZoom Installing and Adjusting the CineWide Anamorphic Lens Assembly to Lens MotorCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Configure Lens Motor Adjust the AnamorphicAdjusting the Horizontal X Lens Position TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Using the On-Screen Menus OperationMemory Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Remote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsHdtv programs in their Native aspect ratioPicture Remote Aspect Ratio Control Description KeyPicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Symptom Possible Causes SolutionPage If you are using a PC to communicate with Serial CommunicationsCommand Description Response Input Selection CommandsAspect Ratio Commands Command Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select buttonPage Specifications VX-22i SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsSpecifications are subject to change without notice VX-22i Dimensions VX-22i/CineWide with AutoScope DimensionsSupported Timings PAL-B/G Page Page Runco CL-810 Owner’s Operating Manual