Vidikron SERIES 1080p manual Connections to the Vision, Connector Panel Access, Connecting Source

Page 36

Installation

3.6

Connections to the Vision 70

Proceed as follows to connect the Vision 70 to your video sources, external controller(s) – if present – and AC power.

When connecting your equipment:

•Turn off all equipment before making any connections.

•Use the correct signal cables for each source.

•Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them.

Connector Panel Access ➤	To access the connector panel, press
	the door release button so it pops out.
	Turn the knob clockwise or
	counter-clockwise and pull gently on it
	to open the door.
Connecting Source ➤	Connect your video sources to the Vision 70 as shown and described in the sections that
Components to the Vision 70	follow.

HDMI/DVI Connections: See Figure 3-8. With an HDMI source, use the included

HDMI-to-HDMI cable; with a DVI source, use the included DVI-to-HDMI cable.

Use the HDMI input whenever possible. This ensures the highest video

Tip	quality because the signal is carried in the digital domain throughout the

	entire signal path, from source component output into the projector.

S-VID /

VID-S

HDMI or DVI Source

(DVD Player or HD Set Top Box)

Figure 3-8. HDMI/DVI Source Connections

24	Vidikron Vision 70 Series Owner’s Operating Manual

Image 36

Contents Series 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents 1List of Figures List of Figures Xii 1Introduction About This ManualUsing This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 70 at a Glance565 Vision 70 Connector Panel Cable Access Door Open to access connectorsBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlOn / OFF Source Selection Buttons Comp 1 SD ComponentVID S-Video Comp 2 HD ComponentMemory Preset Buttons Cursor KeysPicture-In-Picture PIP / Picture-By-Picture PBP Controls VAC V2 Aperture ControlRemote Control/Built-In Keypad Functional Comparison Motorized Lens Controls3Installation Remote ControlOperation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 70/CineWide or Vision 70/CineWideInstallation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsThrow Ratios for the Vision 70 Series Throw Range Throw RatioProjector Model VisionCeiling Installation Floor InstallationVertical and Horizontal PositionFolded Optics Installing the Optional CineWide Lens Mount Vision 70/CineWide with AutoScope Lens Motor Bottom View Ceiling Mount Extension Brackets Ceiling mounting plate Vision 70/CineWide with Lens Base PlateAdjusting the Projector Mounting the VisionFloor Mounting Upright Connector Panel Access Connecting SourceConnections to the Vision RGB Connections 10. Progressive Component Video Connections DTV or Progressive Component YPbPr SourceDTV Source DVD Player, VCR Satellite Receiver Etc 11. Composite, S-Video and Component Video ConnectionsConnection 12. RS-232 Control System Connection14. Connecting the 12-Volt Trigger Output to Other Equipment Turning on the Power Focus Zoom Vertical Lens Shift Installing and Adjusting the CineWide Anamorphic Lens Vision 70/CineWideAdjusting the Lens Height Y Anamorphic Lens Top View Adjustment Vision 70/CineWide withAutoScope Attach Lens Mounting Assembly to Lens Motor Carriage Plate 17. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using Picture-In-Picture/ Picture-By-Picture PIP/PBP 4OperationSelecting Video Memory Selecting an Aspect Ratio Selecting An Input SourceUsing the On-Screen Menus Adjust InstallationService PicturePicture Adjust Main MenuPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionAspect Ratio Settings DescriptionRemote Projector Status Installation Exit to return to the previous menu or Menu to exitService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation 5Maintenance and Troubleshooting Lamp ReplacementLamp assembly for replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Correct Vision 70 input Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial CommunicationsSerial Communications Serial Commands Serial Commands 7Specifications Vision 70 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsLimited Warranty Specifications are subject to change without noticeRegulatory Approvals Vision 70 Dimensions Vision 70 DimensionsVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron