Vidikron SERIES 1080p manual Exit to return to the previous menu or Menu to exit, Installation

Page 65

Operation

Lamp Hours: Lamp Hours indicates how long the currently-installed lamp has been in service. (This part of the menu is read-only.)

To access the Installation adjustments, press MENU, then press the or button to highlight Installation and press ENTER. The Installation sub-menu, shown at left, appears. Press EXIT to return to the previous menu or press MENU to close all menus.

When you change a setting in the Installation menu, the change takes

Note effect immediately; you do not need to press ENTER afterwards. (Press

EXIT to return to the previous menu or MENU to exit.)

Language: Press the or button to select from the available languages (English, French, Spanish, German and Italian).

Picture Configuration: Press the or button to change the orientation of the projected image. The Vision 70 can be installed on a ceiling or in a rear-screen configuration with one or more mirrors. There are four settings: Floor Front, Ceiling Front, Floor Rear and Ceiling Rear.

Keystone: To correct distortion resulting from the angle of projection, select Keystone and use the or button to make the image rectangular.

Vidikron recommends that the keystone feature not be used unless

Tip

absolutely necessary, as it may cause artifacts in the image.

 

OSD Position: To adjust the horizontal and vertical position of the OSD, select OSD Position and press ENTER. Then, press the or button to select Horizontal or Vertical and use the or button to adjust.

OSD Timer: Use the or button to set the OSD Timer. This timer controls how long the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in 3-second increments. When you set the OSD Timer to 0, the menus remain on-screen until you hide them by pressing MENU.

PIP/PBP Setup: Select PIP/PBP Setup from the Installation menu to change the PIP/PBP settings.

•PIP/PBP Enable: Press the or button to select PIP/PBP Enable, then press ENTER. Press the or button to select Off or On, then press ENTER.

•PIP Set Up: Press the or button to select PIP Set Up, then press ENTER. Press the or button to select PIP Off, Graphic in Video or Video in Graphic, then press ENTER.

•PBP Set Up: Press the or button arrows to select PBP Set Up, then press ENTER. Press the or button to select PBP Off, Graphic by Video or Video by Graphic, then press ENTER.

Background Color: Press the or button to select the image Background Color (grey, blue or white). The Background Color appears when no incoming signal is present.

Installation

Installation

Language

Picture Configuration

Keystone

OSD Position

OSD Timer

PIP/PBP Setup

Background Color

Vidikron Vision 70 Series Owner’s Operating Manual

53

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Series 1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents 1List of Figures List of Figures Xii About This Manual 1IntroductionThey also provide supplemental information Using This ManualPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories Vision 70 at a Glance POWER/STANDBY LED Indicates power status as follows565 Cable Access Door Open to access connectors Vision 70 Connector PanelBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlSource Selection Buttons Comp 1 SD Component On / OFFVID S-Video Comp 2 HD ComponentCursor Keys Memory Preset ButtonsPicture-In-Picture PIP / Picture-By-Picture PBP Controls VAC V2 Aperture ControlMotorized Lens Controls Remote Control/Built-In Keypad Functional ComparisonOperation 3InstallationRemote Control Installation Overview Quick SetupStep Procedure For Details, Refer to If installing a Vision 70/CineWide or Vision 70/CineWideProjector Installation Options Installation ConsiderationsInstallation Type Advantages ConsiderationsThrow Range Throw Ratio Throw Ratios for the Vision 70 SeriesProjector Model VisionFloor Installation Ceiling InstallationVertical and Horizontal PositionFolded Optics Installing the Optional CineWide Lens Mount Vision 70/CineWide with AutoScope Lens Motor Bottom View Ceiling Mount Extension Brackets Vision 70/CineWide with Lens Base Plate Ceiling mounting plateFloor Mounting Upright Adjusting the ProjectorMounting the Vision Connections to the Vision Connector Panel AccessConnecting Source RGB Connections DTV or Progressive Component YPbPr Source 10. Progressive Component Video Connections11. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc12. RS-232 Control System Connection Connection14. Connecting the 12-Volt Trigger Output to Other Equipment Turning on the Power Focus Zoom Vertical Lens Shift Vision 70/CineWide Installing and Adjusting the CineWide Anamorphic LensAdjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 70/CineWide with 17. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry 4Operation Using Picture-In-Picture/ Picture-By-Picture PIP/PBPSelecting Video Memory Selecting an Aspect Ratio Selecting An Input SourceUsing the On-Screen Menus Installation AdjustService PictureMain Menu Picture AdjustTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionDescription Aspect Ratio SettingsRemote Projector Status Exit to return to the previous menu or Menu to exit InstallationService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Correct Vision 70 input Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands 6Serial CommunicationsSerial Communications Serial Commands Serial Commands Vision 70 Specifications 7SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsRegulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 70 Dimensions Vision 70 DimensionsVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron
Top Page Image Contents