Vidikron SERIES 1080p manual Adjustment, Vision 70/CineWide with, AutoScope

Page 47

Installation

Once the proper lens angle has been set, firmly tighten the Yaw/Z-Adjustment Levers to secure the lens in place.

The Vision 70 Anamorphic lens mount kit consists of everything shown in Figure 3-16.Some	Anamorphic Lens Installation
components shipped with your projector may differ slightly from what is shown in these	and Adjustment -
instructions.	Vision 70/CineWide with
	AutoScope
1 Lens Adapter Ring
2 Pitch Adjustment Yoke
for Lens

3 Height/Y Adjustment

T-Screw (2x)

and Washer (2x)

4 Pitch Adjustment

T-Screw (2x)

and Washer (2x)

8Yaw/X Adjustment

Levers (2x) and	5 Anamorphic Lens
Washers (2x)	Holder

61/4-20 Hex Bolts (2x)

7 AutoScope Carriage Plate

Figure 3-16. Anamorphic Lens Mounting Assembly - Exploded View

Vidikron Vision 70 Series Owner’s Operating Manual

35

Image 47

Contents Series 1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents 1List of Figures List of Figures Xii About This Manual 1IntroductionIf you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 70 at a Glance POWER/STANDBY LED Indicates power status as follows565 Cable Access Door Open to access connectors Vision 70 Connector PanelBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlComp 2 HD Component On / OFFSource Selection Buttons Comp 1 SD Component VID S-VideoVAC V2 Aperture Control Memory Preset ButtonsCursor Keys Picture-In-Picture PIP / Picture-By-Picture PBP ControlsMotorized Lens Controls Remote Control/Built-In Keypad Functional ComparisonOperation 3InstallationRemote Control If installing a Vision 70/CineWide or Vision 70/CineWide Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeVision Throw Ratios for the Vision 70 SeriesThrow Range Throw Ratio Projector ModelPosition Ceiling InstallationFloor Installation Vertical and HorizontalFolded Optics Installing the Optional CineWide Lens Mount Vision 70/CineWide with AutoScope Lens Motor Bottom View Ceiling Mount Extension Brackets Vision 70/CineWide with Lens Base Plate Ceiling mounting plateFloor Mounting Upright Adjusting the ProjectorMounting the Vision Connections to the Vision Connector Panel AccessConnecting Source RGB Connections DTV or Progressive Component YPbPr Source 10. Progressive Component Video Connections11. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc12. RS-232 Control System Connection Connection14. Connecting the 12-Volt Trigger Output to Other Equipment Turning on the Power Focus Zoom Vertical Lens Shift Vision 70/CineWide Installing and Adjusting the CineWide Anamorphic LensAdjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 70/CineWide with 17. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Selecting an Aspect Ratio Selecting An Input Source Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting Video MemoryUsing the On-Screen Menus Picture AdjustInstallation ServiceMain Menu Picture AdjustTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionDescription Aspect Ratio SettingsRemote Projector Status Exit to return to the previous menu or Menu to exit InstallationService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Correct Vision 70 input Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Commands Vision 70 Specifications 7SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsRegulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 70 Dimensions Vision 70 DimensionsVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron