Vidikron SERIES 1080p manual Turning on the Power

Page 42

Installation

Connecting to AC Power ➤ Projector: The Vision 70 ships with various types of AC power cords. Choose the one that is appropriate to your locale.

Plug the female end of the power cord into the AC receptacle on the rear of the projector (AC 100V ~ 240V). Then, connect the other end to your AC power source.

Power switch

AutoScope Lens Motor: With AutoScope-equipped projectors, an additional power cord is provided for the lens motor. Plug the female end of the AC power cord into the AC input on the rear of the lens motor assembly. Connect the other end to a 110 VAC power source.

The input voltage to the AutoScope lens motor must be between 100 and

Caution 120 VAC. Do not connect the AutoScope lens motor to a 200-240 VAC power source!

AutoScope Lens Motor (Rear)

to

110 VAC Power

Power AC Input

Switch

3.7

Turning on the Power

1.Turn on your source components.

2.If this is an AutoScope-equipped projector, turn on the main power switch at the rear of the AutoScope lens motor. The lens motor power switch is located next to the AC input (see above).

3.Turn on the main power switch at the rear of the projector. The POWER LED lights orange. The LAMP and TEMP LEDs light red briefly, then go out.

4.Press the ON button on the remote control to turn on the Vision 70. The POWER LED flashes orange to indicate that it is warming up.

5.When the projector is ready for use, the POWER LED lights green.

6.“Searching...” appears on the screen before the Vision 70 identifies the input signal and remains there until a valid signal is detected.

7.If an incompatible input signal exceeds the range of the projector, a “No signal supported” message appears on the screen. This message remains on the screen until you change the input signal.

30	Vidikron Vision 70 Series Owner’s Operating Manual

Image 42

Contents Series 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents 1List of Figures List of Figures Xii 1Introduction About This ManualPerformance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 70 at a Glance565 Vision 70 Connector Panel Cable Access Door Open to access connectorsBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlVID S-Video On / OFFSource Selection Buttons Comp 1 SD Component Comp 2 HD ComponentPicture-In-Picture PIP / Picture-By-Picture PBP Controls Memory Preset ButtonsCursor Keys VAC V2 Aperture ControlRemote Control/Built-In Keypad Functional Comparison Motorized Lens Controls3Installation Remote ControlOperation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 70/CineWide or Vision 70/CineWideInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsProjector Model Throw Ratios for the Vision 70 SeriesThrow Range Throw Ratio VisionVertical and Horizontal Ceiling InstallationFloor Installation PositionFolded Optics Installing the Optional CineWide Lens Mount Vision 70/CineWide with AutoScope Lens Motor Bottom View Ceiling Mount Extension Brackets Ceiling mounting plate Vision 70/CineWide with Lens Base PlateAdjusting the Projector Mounting the VisionFloor Mounting Upright Connector Panel Access Connecting SourceConnections to the Vision RGB Connections 10. Progressive Component Video Connections DTV or Progressive Component YPbPr SourceDTV Source DVD Player, VCR Satellite Receiver Etc 11. Composite, S-Video and Component Video ConnectionsConnection 12. RS-232 Control System Connection14. Connecting the 12-Volt Trigger Output to Other Equipment Turning on the Power Focus Zoom Vertical Lens Shift Installing and Adjusting the CineWide Anamorphic Lens Vision 70/CineWideAdjusting the Lens Height Y Anamorphic Lens Top View Adjustment Vision 70/CineWide withAutoScope Attach Lens Mounting Assembly to Lens Motor Carriage Plate 17. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Selecting Video Memory Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting an Aspect Ratio Selecting An Input SourceUsing the On-Screen Menus Service AdjustInstallation PicturePicture Adjust Main MenuPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionAspect Ratio Settings DescriptionRemote Projector Status Installation Exit to return to the previous menu or Menu to exitService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation 5Maintenance and Troubleshooting Lamp ReplacementLamp assembly for replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Correct Vision 70 input Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsSerial Communications Serial Commands Serial Commands 7Specifications Vision 70 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsLimited Warranty Specifications are subject to change without noticeRegulatory Approvals Vision 70 Dimensions Vision 70 DimensionsVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron