Vidikron SERIES 1080p manual Installing the Optional CineWide Lens Mount

Page 31

Installation

If you are installing a Vision 70/CineWide or Vision 70/CineWide with AutoScope, proceed as follows to install the AutoScope lens motor or fixed CineWide base plate.

1. Do not install the CineWide lens yet, only the fixed CineWide base plate

Note or AutoScope lens motor. You will install the CineWide lens after you

install the projector and adjust the primary lens.

2.Some components shipped with your projector may differ slightly from what is shown in these instructions.

If you are installing a Vision 70/CineWide, proceed with Installing the Lens Base Plate (Vision 70/CineWide) on page 22.

Installing the Lens Motor (Vision 70/CineWide with AutoScope): To install the AutoScope lens motor on a Vision 70/CineWide with AutoScope:

1.Place the projector upside down on a blanket or other soft surface.

2.Remove the two height adjusters at the front of the projector by turning them counterclockwise until they come out.

3.Line up the eight mounting holes on the lens motor housing with those on the bottom of the projector.

3.4

Installing the Optional CineWide Lens Mount

Attaching the AutoScope

Lens Motor or Fixed

CineWide Base Plate to

Projector

Vidikron Vision 70 Series Owner’s Operating Manual

19

Image 31

Contents Series 1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents 1List of Figures List of Figures Xii About This Manual 1IntroductionIf you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 70 at a Glance POWER/STANDBY LED Indicates power status as follows565 Cable Access Door Open to access connectors Vision 70 Connector PanelBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlComp 2 HD Component On / OFFSource Selection Buttons Comp 1 SD Component VID S-VideoVAC V2 Aperture Control Memory Preset ButtonsCursor Keys Picture-In-Picture PIP / Picture-By-Picture PBP ControlsMotorized Lens Controls Remote Control/Built-In Keypad Functional ComparisonRemote Control 3InstallationOperation If installing a Vision 70/CineWide or Vision 70/CineWide Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeVision Throw Ratios for the Vision 70 SeriesThrow Range Throw Ratio Projector ModelPosition Ceiling InstallationFloor Installation Vertical and HorizontalFolded Optics Installing the Optional CineWide Lens Mount Vision 70/CineWide with AutoScope Lens Motor Bottom View Ceiling Mount Extension Brackets Vision 70/CineWide with Lens Base Plate Ceiling mounting plateMounting the Vision Adjusting the ProjectorFloor Mounting Upright Connecting Source Connector Panel AccessConnections to the Vision RGB Connections DTV or Progressive Component YPbPr Source 10. Progressive Component Video Connections11. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc12. RS-232 Control System Connection Connection14. Connecting the 12-Volt Trigger Output to Other Equipment Turning on the Power Focus Zoom Vertical Lens Shift Vision 70/CineWide Installing and Adjusting the CineWide Anamorphic LensAdjusting the Lens Height Y Anamorphic Lens Top View Vision 70/CineWide with AdjustmentAutoScope 17. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Selecting an Aspect Ratio Selecting An Input Source Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting Video MemoryUsing the On-Screen Menus Picture AdjustInstallation ServiceMain Menu Picture AdjustTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionDescription Aspect Ratio SettingsRemote Projector Status Exit to return to the previous menu or Menu to exit InstallationService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Correct Vision 70 input Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Commands Vision 70 Specifications 7SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsSpecifications are subject to change without notice Limited WarrantyRegulatory Approvals Vision 70 Dimensions Vision 70 DimensionsVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron