Vidikron 140/150 manual Code Description Power and Cooling

Page 100

Maintenance and Troubleshooting

Table 5-2. Vision 140/150 Error Codes (continued)

Code	Description

	Power and Cooling

46	Red DMD heat sink overheated.

47	Green DMD heat sink overheated.

48	Blue DMD heat sink overheated.

49	Prism overheated.

4C	Projector shutdown due to critical error.

C0	Lamp blower failure (lamp not turned on).

51	LVPS fan failed (Fan 1).

52	LVPS/Red cooling fan failed (Fan 2).

53	DC lamp fan failed (Vision 140; Fan 3).

54	Red DMD heatsink fan failed (Fan 4).

55	Green DMD heatsink fan failed (Fan 5).

56	Blue DMD heatsink fan failed (Fan 6).

57	TIPM fan failed (Fan 7).

58	TIPM fan failed (Fan 8).

Note: To clear a system error, press the EXIT key (on the projector’s rear-panel keypad) twice. If necessary, reset the projector by powering it off, allowing it to cool and powering it on again. Contact your Vidikron dealer or Vidikron technical support if the error persists.

88	Vision Model 140/150 Owner’s Operating Manual

Image 100

Contents 140/150 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsTable of Contents 1List of Figures List of Figures About This Manual Carriage return must be used after each command or stringThis Manual Using This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories Vision 140/150 at a Glance Vision 140/150 Top/Rear/Front ViewAdjustable Feet TOP IR Sensor BUILT-IN KeypadInput Panel LED Status DisplayVision 140/150 Input Panel RemoteEthernet Input 1 RgbhvVision 140/150 Rear-Panel Keypad UP Button Left ButtonDown Button Right ButtonIR Sensor VHD Controller Front PanelVacuum Fluorescent Display VHD Controller Rear Panel Hdmi OUTInputs Composite Video InputPower Input 100 to 240 VAC Main Power SwitchRS-232 Control Port Main AC FuseVision 140/150 Remote Control Unit VHD Controller/Vision 140/150 Remote ControlLight IR Output IndicatorRETURN/EXIT ISF DAY CinemaControls and Functions To install batteries in the remote control Remote ControlOperation Installation Installation Overview Quick SetupStep Procedure For Details, Refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsVision 140/150 Lens Options and Throw Ratios Throw RatioWith 126.9x54-inch ScreenCeiling Installation Floor InstallationPosition Vertical and Horizontal LensHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewInstalling the Optional CineWide Lens Mount Anamorphic lens mounting kit is partially pre-assembled atCeiling-mounting an AutoScope-equipped projector Lens motor installedFloor-Mount Adjusting the Projection Mounting the Vision 140/150Floor Mounting Upright AngleConnections to the Vision 140/150 and VHD Controller Connecting the VHD140/150 Hdmi Connections See Figure Connecting SourceController Digital DTV RGB or Component Video Connections See Figure 11. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 14. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentPower source Connecting an External IR Receiver to the VHD ControllerProjector Turning on the Power Component SD Ntsc 480i 169 V150Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Plate fixed CineWideHorizontal Position X Adjustment Installation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 17. TheaterMaster Remote Control for Vision 140/150 MainControl Functions Disabled Navigating the ProjectorVhd 720p 16x9 night4x3 night Ltrbox nightName 16x9 night Number Sync 26.97 kHz Input 23.98 Hz MenuAuto Source Locked Previous Channel Next Channel InterlaceSupport Native aspect ratio is with the primary lens only. With anSize and Position Menu Installation Adjust Pixel Tracking before Pixel Phase Picture Quality MenuWhite Balance There must be at least two consecutive white pixels present Uncheck this item before exiting this menuBack Porch Clipping Detector Color Enable Red Each settingInstallation Menu LumaCal lamp calibration takes approximately two minutesAbove, the Automatic Lens Calibration setting has no effect Working With the Lamp FactorsValue only 1246 may represent 3500 lumens, for example Easily maintained as the lamp ages RVRInstallation Using the On-Screen Menus 4OperationISF Presets ServiceInput Source Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio Settings Description169 Hdtv programs in theirRemote With a 2.351 screen and aPerform the adjustments in the order listed here PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationYou must enter a passcode to access the Calibration menu CalibrationShould be used by ISF-certified technicians only ISF NightOperation You must enter a passcode to access the Service menu ServiceDo not change the Type setting in this menu Vertical Keystone Correction Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp and Filter Replacement Lamp cover 2 screwsRemoving the Lamp RVR Lens Replacement Removing the Primary LensTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Symptom Trigger CineWide withDescription General Vision 140/150 Error CodesLamp Failures Code Description Power and Cooling Code Description Code Description Miscellaneous Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Multiple serial commandsAspect Ratio Commands Image Preset Commands Output Shift Commands Value Stored? Description Miscellaneous Commands CommandEnter key Serial Communications Vision 140/150 Specifications Vision 140/150 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements Vision DimensionsVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron