Vidikron 140/150 manual Working With the Lamp, Factors

Page 71

Access the Lamp Adjust menu to:

Choose a lamp mode for regulating power and light output.

Change the optical aperture size.

View information pertaining to past and present lamps.

Record the lamp serial number in the projector’s memory.

Lamp Hours (read-only):Lamp Hours shows the number of hours logged on the current lamp. Whenever you record a new lamp serial number, the Vision 140/150 automatically resets this value to zero and begins to log time for the new lamp.

Lamp S/N (read-only):Lamp S/N is the serial number recorded for the current lamp. When you install a new lamp and enter its serial number, the number appears here.

Lamp Message: Enter a check mark for Lamp Message to enable a warning message that appears upon power-up when the lamp has reached the specified lamp limit and should be replaced. Delete the check mark to prevent display of this message – instead, when your lamp expires, only the status display messages on the back of the projector will provide a visual warning to replace the lamp.

1. It is recommended that the Lamp Message check box remain enabled.

Note

2. When a lamp warning message appears, press EXIT to temporarily dismiss the warning. The message will continue to appear upon power-up until you install a new lamp.

Lamp Limit: Set Lamp Limit to the number of hours you expect to log on the current lamp before replacing it. This will trigger a lamp message on-screen (if enabled).

1. If you change modes over the life of a lamp, the lamp limit you

Note

originally expected may no longer be possible.

 

 

2. Turning the lamp on and off reduces lamp life significantly, as do other

 

factors.

 

3. It is recommended that Lamp Limit not exceed the expected lamp life,

 

otherwise a lamp could become dangerously fragile with overuse.

3.13

Working With the Lamp

Lamp Adjust

Lamp Hours

147

Lamp S/N

123456789

1. Lamp Message

2.Lamp Limit 1000

3. Lamp Mode Power

4.Power 500

5.

Intensity

0

6.

RVR

3

7.Lamp History

8.Change Lamp

9.Reserved

Vision Model 140/150 Owner’s Operating Manual

59

Image 71
Contents 140/150 Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Serial Communications Maintenance and TroubleshootingSpecifications OperationTable of Contents 1List of Figures List of Figures This Manual Carriage return must be used after each command or stringAbout This Manual If you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 140/150 Top/Rear/Front View Vision 140/150 at a GlanceLED Status Display Adjustable FeetTOP IR Sensor BUILT-IN Keypad Input PanelInput 1 Rgbhv Vision 140/150 Input PanelRemote EthernetVision 140/150 Rear-Panel Keypad Right Button UP ButtonLeft Button Down ButtonVacuum Fluorescent Display VHD Controller Front PanelIR Sensor Composite Video Input VHD Controller Rear PanelHdmi OUT InputsMain AC Fuse Power Input 100 to 240 VACMain Power Switch RS-232 Control PortVHD Controller/Vision 140/150 Remote Control Vision 140/150 Remote Control UnitRETURN/EXIT IR Output IndicatorLight Cinema ISF DAYControls and Functions Operation Remote ControlTo install batteries in the remote control Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview Advantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeScreen Vision 140/150 Lens Options and Throw RatiosThrow Ratio With 126.9x54-inchVertical and Horizontal Lens Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Lens Assembly Front View Installing the Projection LensAnamorphic lens mounting kit is partially pre-assembled at Installing the Optional CineWide Lens MountFloor-Mount Lens motor installedCeiling-mounting an AutoScope-equipped projector Angle Adjusting the ProjectionMounting the Vision 140/150 Floor Mounting Upright140/150 Connecting the VHDConnections to the Vision 140/150 and VHD Controller Controller Connecting SourceHdmi Connections See Figure 11. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See Figure14. RS-232 Control System Connection ConnectionEquipment Connecting 12-Volt TriggerProjector Connecting an External IR Receiver to the VHD ControllerPower source Component SD Ntsc 480i 169 V150 Turning on the PowerFocus Zoom Vertical and Horizontal Lens Shift Adjusting the Picture Orientation Primary Lens AdjustmentsPlate fixed CineWide Installing and Adjusting the CineWide Anamorphic LensHorizontal Position X Adjustment Installation Geometry Anamorphic Lens Top ViewWrong Position Calibrating Projector Input 2 DVI Main 17. TheaterMaster Remote Control for Vision 140/150Control Functions Navigating the Projector DisabledLtrbox night Vhd 720p16x9 night 4x3 nightInterlace Name 16x9 nightNumber Sync 26.97 kHz Input 23.98 Hz Menu Auto Source Locked Previous Channel Next ChannelSize and Position Menu Native aspect ratio is with the primary lens only. With anSupport Installation Picture Quality Menu Adjust Pixel Tracking before Pixel PhaseWhite Balance Uncheck this item before exiting this menu There must be at least two consecutive white pixels presentEach setting Back Porch Clipping Detector Color Enable RedLumaCal lamp calibration takes approximately two minutes Installation MenuAbove, the Automatic Lens Calibration setting has no effect Factors Working With the LampValue only 1246 may represent 3500 lumens, for example RVR Easily maintained as the lamp agesInstallation 4Operation Using the On-Screen MenusAspect Ratio ISF PresetsService Input SourceAspect Ratio Main MenuInput Source Hdtv programs in their Aspect Ratio SettingsDescription 169With a 2.351 screen and a RemotePicture Perform the adjustments in the order listed hereTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting SharpnessInformation ISF PresetsISF Night You must enter a passcode to access the Calibration menuCalibration Should be used by ISF-certified technicians onlyOperation Do not change the Type setting in this menu ServiceYou must enter a passcode to access the Service menu Keystone Correction Vertical Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp cover 2 screws Lamp and Filter ReplacementRemoving the Lamp RVR Removing the Primary Lens Lens ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Trigger CineWide with SymptomLamp Failures Vision 140/150 Error CodesDescription General Code Description Power and Cooling Code Description Code Description Miscellaneous Multiple serial commands Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsAspect Ratio Commands Image Preset Commands Output Shift Commands Enter key CommandValue Stored? Description Miscellaneous Commands Serial Communications Vision 140/150 Specifications Vision 140/150 SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power Requirements VisionVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron