Vidikron 140/150 manual There must be at least two consecutive white pixels present

Page 67

Installation

1. There must be at least two consecutive white pixels present in the

Note image for the “Pre-Calibration” function to work properly. Otherwise, input levels may produce skewed colors, particularly in non-video images.

2.Uncheck this item before exiting this menu.

Black Levels and White Levels: To check your image and adjust these controls:

1.Make sure overall “White Level” (contrast) and “Black Level” (brightness) settings are both set to near 50. (Not required for “Pre-Calibration” adjustment.)

2.Check the color temperature setup using an internal grayscale test pattern, making sure to obtain a neutral grayscale. (Not required for “Pre-Calibration” adjustment.)

3.If the blacks and/or whites appear OK, input levels do not need adjustment. If black levels are too high (and/or whites are too low, which is rare), you likely have a noisy source that is producing skewed input levels. Continue with Step 4.

4.Temporarily enable “Pre-Calibration” in the White Balance submenu. Wait for all six values to stabilize. Alternatively, do not use “Pre-Calibration” — reduce black levels manually instead. Judge by eye and change one or more of the six levels as necessary to obtain proper blacks and whites. You may want to see only a certain color while adjusting; if so, use the “Color Enable” option (described below).

5.Clear the “Pre-Calibration” check box and exit the White Balance menu.

Auto Color Enable: When a check mark is present, selecting a specific black level or drive to adjust will automatically enable the corresponding color in the display. Delete the check mark to see all colors.

Clamping: This option can brighten the image produced from certain high-resolution, high-frequency graphic sources. For almost all sources, the best clamp location is automatically selected by the projector.

• Use the normal Back Porch location if the image is either sufficiently bright or overly bright.

• Select Sync Tip if the image appears unusually dim, if there are horizontal streaks across the image, or if there is significant color drift. This moves the clamping pulse from the normal back porch location (which is likely too short) to the tip of the horizontal sync pulse.

Tri Level is typically recommended for an HDTV source where the back porch is also short, or for video sources or any RGB source with sync information included on the video (for example, sync-on-green).

Clipping Detector: The Clipping Detector is a tool to assist with defining individual input levels, enabling you to accurately set the white balance for any particular source with the appropriate image.

Enabling the Clipping Detector activates a special operating mode for detecting only pixels that are considered black or white; all other levels are displayed as a mid-level gray. When used with a smooth grayscale pattern in which black and white are known to be at opposite edges of the image, you can watch these isolated areas while adjusting individual black and white levels until both black and white edges are just visible and distinguished from neighboring pixels. Images from this source will then display correct

Vision Model 140/150 Owner’s Operating Manual

55

Image 67
Contents 140/150 Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Serial Communications Maintenance and TroubleshootingSpecifications OperationTable of Contents 1List of Figures List of Figures About This Manual Carriage return must be used after each command or stringThis Manual If you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 140/150 Top/Rear/Front View Vision 140/150 at a GlanceLED Status Display Adjustable FeetTOP IR Sensor BUILT-IN Keypad Input PanelInput 1 Rgbhv Vision 140/150 Input PanelRemote EthernetVision 140/150 Rear-Panel Keypad Right Button UP ButtonLeft Button Down ButtonIR Sensor VHD Controller Front PanelVacuum Fluorescent Display Composite Video Input VHD Controller Rear PanelHdmi OUT InputsMain AC Fuse Power Input 100 to 240 VACMain Power Switch RS-232 Control PortVHD Controller/Vision 140/150 Remote Control Vision 140/150 Remote Control UnitLight IR Output IndicatorRETURN/EXIT Cinema ISF DAYControls and Functions To install batteries in the remote control Remote ControlOperation Installation Installation Overview Quick SetupStep Procedure For Details, Refer to Advantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeScreen Vision 140/150 Lens Options and Throw RatiosThrow Ratio With 126.9x54-inchVertical and Horizontal Lens Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Lens Assembly Front View Installing the Projection LensAnamorphic lens mounting kit is partially pre-assembled at Installing the Optional CineWide Lens MountCeiling-mounting an AutoScope-equipped projector Lens motor installedFloor-Mount Angle Adjusting the ProjectionMounting the Vision 140/150 Floor Mounting UprightConnections to the Vision 140/150 and VHD Controller Connecting the VHD140/150 Hdmi Connections See Figure Connecting SourceController 11. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See Figure14. RS-232 Control System Connection ConnectionEquipment Connecting 12-Volt TriggerPower source Connecting an External IR Receiver to the VHD ControllerProjector Component SD Ntsc 480i 169 V150 Turning on the PowerFocus Zoom Vertical and Horizontal Lens Shift Adjusting the Picture Orientation Primary Lens AdjustmentsPlate fixed CineWide Installing and Adjusting the CineWide Anamorphic LensHorizontal Position X Adjustment Installation Geometry Anamorphic Lens Top ViewWrong Position Calibrating Projector Input 2 DVI Main 17. TheaterMaster Remote Control for Vision 140/150Control Functions Navigating the Projector DisabledLtrbox night Vhd 720p16x9 night 4x3 nightInterlace Name 16x9 nightNumber Sync 26.97 kHz Input 23.98 Hz Menu Auto Source Locked Previous Channel Next ChannelSupport Native aspect ratio is with the primary lens only. With anSize and Position Menu Installation Picture Quality Menu Adjust Pixel Tracking before Pixel PhaseWhite Balance Uncheck this item before exiting this menu There must be at least two consecutive white pixels presentEach setting Back Porch Clipping Detector Color Enable RedLumaCal lamp calibration takes approximately two minutes Installation MenuAbove, the Automatic Lens Calibration setting has no effect Factors Working With the LampValue only 1246 may represent 3500 lumens, for example RVR Easily maintained as the lamp agesInstallation 4Operation Using the On-Screen MenusAspect Ratio ISF PresetsService Input SourceInput Source Main MenuAspect Ratio Hdtv programs in their Aspect Ratio SettingsDescription 169With a 2.351 screen and a RemotePicture Perform the adjustments in the order listed hereTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting SharpnessInformation ISF PresetsISF Night You must enter a passcode to access the Calibration menuCalibration Should be used by ISF-certified technicians onlyOperation You must enter a passcode to access the Service menu ServiceDo not change the Type setting in this menu Keystone Correction Vertical Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp cover 2 screws Lamp and Filter ReplacementRemoving the Lamp RVR Removing the Primary Lens Lens ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Trigger CineWide with SymptomDescription General Vision 140/150 Error CodesLamp Failures Code Description Power and Cooling Code Description Code Description Miscellaneous Multiple serial commands Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsAspect Ratio Commands Image Preset Commands Output Shift Commands Value Stored? Description Miscellaneous Commands CommandEnter key Serial Communications Vision 140/150 Specifications Vision 140/150 SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power Requirements VisionVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron