Vidikron 140/150 manual Home Theater Calibration Specifications, Industry-Standard Specifications

Page 110

Specifications

Table 7-1. Vision 140/150 Specifications (continued)

Brightness and Contrast:

Cinema Standards Measurement System (CSMS)

 

Specifications

 

-

Brightness: 86.5 foot-Lamberts (fL) (Vision 140);

 

 

102.0 fL (Vision 150)

 

-

Contrast Ratio (variable, based on lens aperture setting):

 

 

235:1 - 275:1 (Vision 140); 224:1 - 275:1 (Vision 150)

 

These measurements are taken from the projector in a controlled, home

 

theater environment. All measurements are made to ANSI/NAPM

 

IT7.228-1997 specifications using the Photo Research PR-650

 

SpectraColorimeter and Minolta LS-100 Luminance Meter, Video

 

Essentials test DVD and a 1.3 gain, 72-inch wide screen. The projector is

 

calibrated to a color temperature of 6,500K and has a minimum of 150

 

hours of usage.

 

The foot-Lambert (fL) is the unit of measurement used in commercial

 

movie theaters to express image brightness at the screen surface. The

 

Society of Motion Picture and Television Engineers (SMPTE) specifies

 

16 fL as the target image brightness for film-based projectors using an

 

open gate (without film in the projector). More importantly, today

 

SMPTE specifies 12 fL as the target image brightness in Digital Cinema

 

theaters. The foot-Lambert measurement is dependent on screen size,

 

screen gain and projector light output.

 

Home Theater Calibration Specifications

 

-

Light Output: 2750 ANSI Lumens (Vision 140);

 

 

3517 ANSI Lumens (Vision 150)

 

-

Contrast Ratio (variable, based on lens aperture setting):

 

 

235:1 - 275:1 (Vision 140); 224:1 - 275:1 (Vision 150)

 

These specifications are obtained by calibrating the projector as

 

described above for CSMS measurements.

 

Industry-Standard Specifications

 

-

Light Output: 4000 ANSI Lumens (Vision 140);

 

 

6000 ANSI Lumens (Vision 150)

 

-

Contrast Ratio (variable, based on lens aperture setting):

 

 

1500:1 - 2000:1

 

These are typical projector brightness and contrast specifications found

 

in most companies’ sales literature. Vidikron includes these

 

measurements in its literature to allow for direct comparison with other

 

manufacturers’ projectors. These measurements are typically taken at

 

9,000K to 13,000K to get expected performance data when the projector

 

is used in professional, commercial and industrial displays.

 

 

Power Requirements:

Vision 140:

 

100 to 240 VAC (auto-sensing), 50/60 Hz, 1,650 Watts

 

Vision 150:

 

200 to 240 VAC, 50/60 Hz, 2,100 Watts

 

 

Operating Environment:

41°F to 95°F (5°C to 35°C), 20% to 80% humidity

 

(non-condensing)

 

 

Dimensions:

See Figure 7-1

 

 

Weight (without lens):

140 lbs. (63.50 kg)

 

 

Regulatory Approvals:

Complies with FCC, CE C-Tick

 

 

Limited Warranty:

Projector: Two (2) years parts and labor from the date of delivery

 

to the end user.

 

Lamp: 1000 hours or six (6) months, whichever comes first.

Specifications are subject to change without notice.

98

Vision Model 140/150 Owner’s Operating Manual

Image 110
Contents 140/150 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsTable of Contents 1List of Figures List of Figures This Manual Carriage return must be used after each command or stringAbout This Manual Performance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories Vision 140/150 at a Glance Vision 140/150 Top/Rear/Front ViewInput Panel Adjustable FeetTOP IR Sensor BUILT-IN Keypad LED Status DisplayEthernet Vision 140/150 Input PanelRemote Input 1 RgbhvVision 140/150 Rear-Panel Keypad Down Button UP ButtonLeft Button Right ButtonVacuum Fluorescent Display VHD Controller Front PanelIR Sensor Inputs VHD Controller Rear PanelHdmi OUT Composite Video InputRS-232 Control Port Power Input 100 to 240 VACMain Power Switch Main AC FuseVision 140/150 Remote Control Unit VHD Controller/Vision 140/150 Remote ControlRETURN/EXIT IR Output IndicatorLight ISF DAY CinemaControls and Functions Operation Remote ControlTo install batteries in the remote control Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsWith 126.9x54-inch Vision 140/150 Lens Options and Throw RatiosThrow Ratio ScreenPosition Ceiling InstallationFloor Installation Vertical and Horizontal LensHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewInstalling the Optional CineWide Lens Mount Anamorphic lens mounting kit is partially pre-assembled atFloor-Mount Lens motor installedCeiling-mounting an AutoScope-equipped projector Floor Mounting Upright Adjusting the ProjectionMounting the Vision 140/150 Angle140/150 Connecting the VHDConnections to the Vision 140/150 and VHD Controller Controller Connecting SourceHdmi Connections See Figure Digital DTV RGB or Component Video Connections See Figure 11. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 14. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentProjector Connecting an External IR Receiver to the VHD ControllerPower source Turning on the Power Component SD Ntsc 480i 169 V150Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Plate fixed CineWideHorizontal Position X Adjustment Installation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 17. TheaterMaster Remote Control for Vision 140/150 MainControl Functions Disabled Navigating the Projector4x3 night Vhd 720p16x9 night Ltrbox nightAuto Source Locked Previous Channel Next Channel Name 16x9 nightNumber Sync 26.97 kHz Input 23.98 Hz Menu InterlaceSize and Position Menu Native aspect ratio is with the primary lens only. With anSupport Installation Adjust Pixel Tracking before Pixel Phase Picture Quality MenuWhite Balance There must be at least two consecutive white pixels present Uncheck this item before exiting this menuBack Porch Clipping Detector Color Enable Red Each settingInstallation Menu LumaCal lamp calibration takes approximately two minutesAbove, the Automatic Lens Calibration setting has no effect Working With the Lamp FactorsValue only 1246 may represent 3500 lumens, for example Easily maintained as the lamp ages RVRInstallation Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source 169 Aspect Ratio SettingsDescription Hdtv programs in theirRemote With a 2.351 screen and aPerform the adjustments in the order listed here PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationShould be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuCalibration ISF NightOperation Do not change the Type setting in this menu ServiceYou must enter a passcode to access the Service menu Vertical Keystone Correction Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp and Filter Replacement Lamp cover 2 screwsRemoving the Lamp RVR Lens Replacement Removing the Primary LensSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Symptom Trigger CineWide withLamp Failures Vision 140/150 Error CodesDescription General Code Description Power and Cooling Code Description Code Description Miscellaneous Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Multiple serial commandsAspect Ratio Commands Image Preset Commands Output Shift Commands Enter key CommandValue Stored? Description Miscellaneous Commands Serial Communications Vision 140/150 Specifications Vision 140/150 SpecificationsPower Requirements Vision Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron