Vidikron 140/150 manual Installing the Projection Lens, Lens Assembly Front View

Page 38

Installation

3.4

Installing the Projection Lens

The projection lens is shipped separately from the projector. Proceed as follows to install the projection lens:

1.Remove the lens plug from the lens opening in the projector.

2.Place the lens cap on the projection lens to protect it from being damaged during the installation process.

3.Remove the rear cap from the lens. This protective cap is only used during shipping to protect the lens from damage.

4.Slide the new lens into the lens opening of the projector. Make sure to align the connector on the side of the lens with the connector assembly on the lens retaining ring; see Figure 3-7.

As you connect the lens, you may have to re-align it slightly until the tabs on the lens fit into the slots in the lens retaining ring.

Figure 3-7. Lens Assembly (Front View)

5.With the lens fully inserted (and connected), turn it clockwise until the lens release button “pops” indicating the lens is fully inserted.

26	Vision Model 140/150 Owner’s Operating Manual

Image 38

Contents 140/150 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsTable of Contents 1List of Figures List of Figures This Manual Carriage return must be used after each command or stringAbout This Manual Performance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories Vision 140/150 at a Glance Vision 140/150 Top/Rear/Front ViewInput Panel Adjustable FeetTOP IR Sensor BUILT-IN Keypad LED Status DisplayEthernet Vision 140/150 Input PanelRemote Input 1 RgbhvVision 140/150 Rear-Panel Keypad Down Button UP ButtonLeft Button Right ButtonVacuum Fluorescent Display VHD Controller Front PanelIR Sensor Inputs VHD Controller Rear PanelHdmi OUT Composite Video InputRS-232 Control Port Power Input 100 to 240 VACMain Power Switch Main AC FuseVision 140/150 Remote Control Unit VHD Controller/Vision 140/150 Remote ControlRETURN/EXIT IR Output IndicatorLight ISF DAY CinemaControls and Functions Operation Remote ControlTo install batteries in the remote control Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsWith 126.9x54-inch Vision 140/150 Lens Options and Throw RatiosThrow Ratio ScreenPosition Ceiling InstallationFloor Installation Vertical and Horizontal LensHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewInstalling the Optional CineWide Lens Mount Anamorphic lens mounting kit is partially pre-assembled atFloor-Mount Lens motor installedCeiling-mounting an AutoScope-equipped projector Floor Mounting Upright Adjusting the ProjectionMounting the Vision 140/150 Angle140/150 Connecting the VHDConnections to the Vision 140/150 and VHD Controller Controller Connecting SourceHdmi Connections See Figure Digital DTV RGB or Component Video Connections See Figure 11. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 14. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentProjector Connecting an External IR Receiver to the VHD ControllerPower source Turning on the Power Component SD Ntsc 480i 169 V150Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Plate fixed CineWideHorizontal Position X Adjustment Installation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 17. TheaterMaster Remote Control for Vision 140/150 MainControl Functions Disabled Navigating the Projector4x3 night Vhd 720p16x9 night Ltrbox nightAuto Source Locked Previous Channel Next Channel Name 16x9 nightNumber Sync 26.97 kHz Input 23.98 Hz Menu InterlaceSize and Position Menu Native aspect ratio is with the primary lens only. With anSupport Installation Adjust Pixel Tracking before Pixel Phase Picture Quality MenuWhite Balance There must be at least two consecutive white pixels present Uncheck this item before exiting this menuBack Porch Clipping Detector Color Enable Red Each settingInstallation Menu LumaCal lamp calibration takes approximately two minutesAbove, the Automatic Lens Calibration setting has no effect Working With the Lamp FactorsValue only 1246 may represent 3500 lumens, for example Easily maintained as the lamp ages RVRInstallation Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source 169 Aspect Ratio SettingsDescription Hdtv programs in theirRemote With a 2.351 screen and aPerform the adjustments in the order listed here PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationShould be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuCalibration ISF NightOperation Do not change the Type setting in this menu ServiceYou must enter a passcode to access the Service menu Vertical Keystone Correction Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp and Filter Replacement Lamp cover 2 screwsRemoving the Lamp RVR Lens Replacement Removing the Primary LensSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Symptom Trigger CineWide withLamp Failures Vision 140/150 Error CodesDescription General Code Description Power and Cooling Code Description Code Description Miscellaneous Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Multiple serial commandsAspect Ratio Commands Image Preset Commands Output Shift Commands Enter key CommandValue Stored? Description Miscellaneous Commands Serial Communications Vision 140/150 Specifications Vision 140/150 SpecificationsPower Requirements Vision Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron