Vidikron 140/150 manual Remote Control, To install batteries in the remote control, Operation

Page 29

3Installation

3.1

Remote Control

To install batteries in the remote control:

Battery Installation

1.Remove the battery cover from the back of the remote control.

2.Insert the batteries included with the remote control. Ensure that the polarities correctly match the and markings inside the battery compartment.

3.Replace the battery cover.

1. Do not mix an old battery with a new one or different types of batteries.

Note

2. If you will not use the remote control for a long time, remove the batteries

to avoid damage from battery leakage.
The remote control can be used to control the Vision 140/150 within the ranges shown in	Notes on Remote Control
Figure 3-1.	Operation

Component SD NTSC		480i
16:9

Approx.

7m/23ft

										LIGHT
	OFF									ON
						ENT
RETURN										MENU
EXIT
					MEMORY
			SOURCE SELECTION

Figure 3-1. Available Range of the Remote Control

Vision Model 140/150 Owner’s Operating Manual

17

Image 29

Contents 140/150 Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Specifications Maintenance and TroubleshootingOperation Serial CommunicationsTable of Contents 1List of Figures List of Figures This Manual Carriage return must be used after each command or stringAbout This Manual They also provide supplemental information Using This ManualPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories Vision 140/150 Top/Rear/Front View Vision 140/150 at a GlanceTOP IR Sensor BUILT-IN Keypad Adjustable FeetInput Panel LED Status DisplayRemote Vision 140/150 Input PanelEthernet Input 1 RgbhvVision 140/150 Rear-Panel Keypad Left Button UP ButtonDown Button Right ButtonVacuum Fluorescent Display VHD Controller Front PanelIR Sensor Hdmi OUT VHD Controller Rear PanelInputs Composite Video InputMain Power Switch Power Input 100 to 240 VACRS-232 Control Port Main AC FuseVHD Controller/Vision 140/150 Remote Control Vision 140/150 Remote Control UnitRETURN/EXIT IR Output IndicatorLight Cinema ISF DAYControls and Functions Operation Remote ControlTo install batteries in the remote control Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview Projector Installation Options Installation ConsiderationsInstallation Type Advantages ConsiderationsThrow Ratio Vision 140/150 Lens Options and Throw RatiosWith 126.9x54-inch ScreenFloor Installation Ceiling InstallationPosition Vertical and Horizontal LensHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Lens Assembly Front View Installing the Projection LensAnamorphic lens mounting kit is partially pre-assembled at Installing the Optional CineWide Lens MountFloor-Mount Lens motor installedCeiling-mounting an AutoScope-equipped projector Mounting the Vision 140/150 Adjusting the ProjectionFloor Mounting Upright Angle140/150 Connecting the VHDConnections to the Vision 140/150 and VHD Controller Controller Connecting SourceHdmi Connections See Figure 11. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See Figure14. RS-232 Control System Connection ConnectionEquipment Connecting 12-Volt TriggerProjector Connecting an External IR Receiver to the VHD ControllerPower source Component SD Ntsc 480i 169 V150 Turning on the PowerFocus Zoom Vertical and Horizontal Lens Shift Adjusting the Picture Orientation Primary Lens AdjustmentsPlate fixed CineWide Installing and Adjusting the CineWide Anamorphic LensHorizontal Position X Adjustment Installation Geometry Anamorphic Lens Top ViewWrong Position Calibrating Projector Input 2 DVI Main 17. TheaterMaster Remote Control for Vision 140/150Control Functions Navigating the Projector Disabled16x9 night Vhd 720p4x3 night Ltrbox nightNumber Sync 26.97 kHz Input 23.98 Hz Menu Name 16x9 nightAuto Source Locked Previous Channel Next Channel InterlaceSize and Position Menu Native aspect ratio is with the primary lens only. With anSupport Installation Picture Quality Menu Adjust Pixel Tracking before Pixel PhaseWhite Balance Uncheck this item before exiting this menu There must be at least two consecutive white pixels presentEach setting Back Porch Clipping Detector Color Enable RedLumaCal lamp calibration takes approximately two minutes Installation MenuAbove, the Automatic Lens Calibration setting has no effect Factors Working With the LampValue only 1246 may represent 3500 lumens, for example RVR Easily maintained as the lamp agesInstallation 4Operation Using the On-Screen MenusService ISF PresetsInput Source Aspect RatioAspect Ratio Main MenuInput Source Description Aspect Ratio Settings169 Hdtv programs in theirWith a 2.351 screen and a RemotePicture Perform the adjustments in the order listed hereTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting SharpnessInformation ISF PresetsCalibration You must enter a passcode to access the Calibration menuShould be used by ISF-certified technicians only ISF NightOperation Do not change the Type setting in this menu ServiceYou must enter a passcode to access the Service menu Keystone Correction Vertical Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp cover 2 screws Lamp and Filter ReplacementRemoving the Lamp RVR Removing the Primary Lens Lens ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Trigger CineWide with SymptomLamp Failures Vision 140/150 Error CodesDescription General Code Description Power and Cooling Code Description Code Description Miscellaneous RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Multiple serial commandsAspect Ratio Commands Image Preset Commands Output Shift Commands Enter key CommandValue Stored? Description Miscellaneous Commands Serial Communications Vision 140/150 Specifications Vision 140/150 SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements Vision DimensionsVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron