Vidikron 140/150 manual Rvr

Page 95

Maintenance and Troubleshooting

13.Press ENTER to accept the change. This adds the new lamp serial number to the Lamp History menu and resets the Lamp Hours timer to “0.” Lamp Mode and Lamp Limit remain as they were for the previous lamp and can be changed at any time.

Lamp Adjust

Lamp Hours	147
Lamp S/N	123456789

1. Lamp Message

2.Lamp Limit 1000

3. Lamp Mode Power

4.Power 500

5.	Intensity	0
6.	RVR	3
7.	Lamp History

8.Change Lamp

9. Reserved

Figure 5-5. Recording the Serial Number of a New Lamp

Always record the serial number of a new lamp. Do this only if you have

Note	just installed a new lamp. This will ensure that the lamp timer is not reset

	on an old lamp and that the number of hours logged on the lamp is
	accurate.
Whenever you replace the lamp – or more often if the projector is installed in an extremely			Filter Replacement
dusty environment – you should also replace the two filters located at the front and right
side of the projector.
1. Loosen the six screws holding right side filter access		Right Side Filter
panel in place. Then, remove the panel.		Access Cover

2.Loosen the screw holding front filter access panel in place. Then, remove the panel.

3.Pull the filters out of the projector and discard. Do not reuse filters.

4.Insert the new filters with the wired side in.

5.Replace the filter access panels and tighten the screws to secure them.

Front Filter Access Cover

Vision Model 140/150 Owner’s Operating Manual

83

Image 95

Contents 140/150 Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Serial Communications Maintenance and TroubleshootingSpecifications OperationTable of Contents 1List of Figures List of Figures This Manual Carriage return must be used after each command or stringAbout This Manual If you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 140/150 Top/Rear/Front View Vision 140/150 at a GlanceLED Status Display Adjustable FeetTOP IR Sensor BUILT-IN Keypad Input PanelInput 1 Rgbhv Vision 140/150 Input PanelRemote EthernetVision 140/150 Rear-Panel Keypad Right Button UP ButtonLeft Button Down ButtonVacuum Fluorescent Display VHD Controller Front PanelIR Sensor Composite Video Input VHD Controller Rear PanelHdmi OUT InputsMain AC Fuse Power Input 100 to 240 VACMain Power Switch RS-232 Control PortVHD Controller/Vision 140/150 Remote Control Vision 140/150 Remote Control UnitRETURN/EXIT IR Output IndicatorLight Cinema ISF DAYControls and Functions Operation Remote ControlTo install batteries in the remote control Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview Advantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeScreen Vision 140/150 Lens Options and Throw RatiosThrow Ratio With 126.9x54-inchVertical and Horizontal Lens Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Lens Assembly Front View Installing the Projection LensAnamorphic lens mounting kit is partially pre-assembled at Installing the Optional CineWide Lens MountFloor-Mount Lens motor installedCeiling-mounting an AutoScope-equipped projector Angle Adjusting the ProjectionMounting the Vision 140/150 Floor Mounting Upright140/150 Connecting the VHDConnections to the Vision 140/150 and VHD Controller Controller Connecting SourceHdmi Connections See Figure 11. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See Figure14. RS-232 Control System Connection ConnectionEquipment Connecting 12-Volt TriggerProjector Connecting an External IR Receiver to the VHD ControllerPower source Component SD Ntsc 480i 169 V150 Turning on the PowerFocus Zoom Vertical and Horizontal Lens Shift Adjusting the Picture Orientation Primary Lens AdjustmentsPlate fixed CineWide Installing and Adjusting the CineWide Anamorphic LensHorizontal Position X Adjustment Installation Geometry Anamorphic Lens Top ViewWrong Position Calibrating Projector Input 2 DVI Main 17. TheaterMaster Remote Control for Vision 140/150Control Functions Navigating the Projector DisabledLtrbox night Vhd 720p16x9 night 4x3 nightInterlace Name 16x9 nightNumber Sync 26.97 kHz Input 23.98 Hz Menu Auto Source Locked Previous Channel Next ChannelSize and Position Menu Native aspect ratio is with the primary lens only. With anSupport Installation Picture Quality Menu Adjust Pixel Tracking before Pixel PhaseWhite Balance Uncheck this item before exiting this menu There must be at least two consecutive white pixels presentEach setting Back Porch Clipping Detector Color Enable RedLumaCal lamp calibration takes approximately two minutes Installation MenuAbove, the Automatic Lens Calibration setting has no effect Factors Working With the LampValue only 1246 may represent 3500 lumens, for example RVR Easily maintained as the lamp agesInstallation 4Operation Using the On-Screen MenusAspect Ratio ISF PresetsService Input SourceAspect Ratio Main MenuInput Source Hdtv programs in their Aspect Ratio SettingsDescription 169With a 2.351 screen and a RemotePicture Perform the adjustments in the order listed hereTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting SharpnessInformation ISF PresetsISF Night You must enter a passcode to access the Calibration menuCalibration Should be used by ISF-certified technicians onlyOperation Do not change the Type setting in this menu ServiceYou must enter a passcode to access the Service menu Keystone Correction Vertical Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp cover 2 screws Lamp and Filter ReplacementRemoving the Lamp RVR Removing the Primary Lens Lens ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Trigger CineWide with SymptomLamp Failures Vision 140/150 Error CodesDescription General Code Description Power and Cooling Code Description Code Description Miscellaneous Multiple serial commands Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsAspect Ratio Commands Image Preset Commands Output Shift Commands Enter key CommandValue Stored? Description Miscellaneous Commands Serial Communications Vision 140/150 Specifications Vision 140/150 SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power Requirements VisionVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron