Vidikron 140/150 manual Above, the Automatic Lens Calibration setting has no effect

Page 70

Geometry and Color

1.

Test Patterns

Grid

2.Keystone 50

3.White Field Uniformity

4.Edge Shading

5.Color Gamut Adjust

6.Color Levels

7.Black Field Uniformity

8.

Default Color Adjustment

ISF Night

9.

OptiCal

 

Calibration and Test Patterns

1.

Test Patterns

Grid

2.

Test Pattern Level

512

3.Freeze Image

4.

Color Enable

White

5.Odd Pixel Adjustment

6.Reserved

7.Clipping Detector

8.Level Detector

9.

Level Value

512

0.Aspect Ratio Overlay

LumaCal Calibrate LumaCal

OptiCal

Full

 

Automatic Lens Calibration

OptiCal (Primary Lens Calibration): OptiCal provides the ability to store and recall focus, zoom and position settings for the primary lens.

To enable OptiCal:

1.Select Installation from the Main Menu.

2.Select Geometry and Color from the Installation menu.

3.Select OptiCal from the Geometry and Color menu.

4.Press ENTER to check the box labeled OptiCal.

1. OptiCal control is a preference setting and is retained between power

Note cycles.

2.OptiCal has no effect on the secondary anamorphic lens, only the primary lens.

5.Press EXIT to exit the Geometry and Color menu.

6.Select Calibration and Test Patterns from the Installation Menu.

7.Select OptiCal from the Calibration and Test Patterns Menu.

OptiCal gives you a choice of three types of lens calibrations:

•A Reference calibration establishes a reference point (starting position) for measuring relative lens movement. All distances are measured from this reference point. A reference calibration is lost when power is removed from the projector and occurs on every power-up as long as OptiCal is enabled.

•A Motion calibration determines the characteristics of each motor and values are saved in the projector’s memory. If OptiCal is enabled and a motion calibration has previously been done, the projector automatically recalls these settings from memory when it’s being powered up and a motion calibration will not take place.

•A Full calibration performs both a Reference calibration and a Motion calibration.

If no calibration has previously been done you may be prompted to do a Full calibration. If a motion calibration has been done, you will be prompted to complete a reference calibration. If both calibrations have been done, the OptiCal checkbox is checked and OptiCal enabled.

When OptiCal is enabled, the Vision 140/150 performs a reference calibration when the projector is turned on. The lens returns to its last saved position (or actual position, if no motion calibration has been done previously). Further adjustments to the zoom, focus and position are automatically saved.

When both OptiCal and Automatic Lens Calibration are enabled, the Vision 140/150 performs a Full calibration when the projector is turned on. During calibration, the shutter closes and the status LED (see Figure 2-3)displays “LC.”

If OptiCal is disabled (refer to OptiCal (Primary Lens Calibration)

Note

above), the Automatic Lens Calibration setting has no effect.

 

58

Vision Model 140/150 Owner’s Operating Manual

Page 69 Page 71
Image 70
Page 69 Page 71
Contents 140/150 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsTable of Contents 1List of Figures List of Figures About This Manual Carriage return must be used after each command or stringThis Manual Performance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories Vision 140/150 at a Glance Vision 140/150 Top/Rear/Front ViewInput Panel Adjustable FeetTOP IR Sensor BUILT-IN Keypad LED Status DisplayEthernet Vision 140/150 Input PanelRemote Input 1 RgbhvVision 140/150 Rear-Panel Keypad Down Button UP ButtonLeft Button Right ButtonIR Sensor VHD Controller Front PanelVacuum Fluorescent Display Inputs VHD Controller Rear PanelHdmi OUT Composite Video InputRS-232 Control Port Power Input 100 to 240 VACMain Power Switch Main AC FuseVision 140/150 Remote Control Unit VHD Controller/Vision 140/150 Remote ControlLight IR Output IndicatorRETURN/EXIT ISF DAY CinemaControls and Functions To install batteries in the remote control Remote ControlOperation Installation Installation Overview Quick SetupStep Procedure For Details, Refer to Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsWith 126.9x54-inch Vision 140/150 Lens Options and Throw RatiosThrow Ratio ScreenPosition Ceiling InstallationFloor Installation Vertical and Horizontal LensHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewInstalling the Optional CineWide Lens Mount Anamorphic lens mounting kit is partially pre-assembled atCeiling-mounting an AutoScope-equipped projector Lens motor installedFloor-Mount Floor Mounting Upright Adjusting the ProjectionMounting the Vision 140/150 AngleConnections to the Vision 140/150 and VHD Controller Connecting the VHD140/150 Hdmi Connections See Figure Connecting SourceController Digital DTV RGB or Component Video Connections See Figure 11. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 14. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentPower source Connecting an External IR Receiver to the VHD ControllerProjector Turning on the Power Component SD Ntsc 480i 169 V150Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Plate fixed CineWideHorizontal Position X Adjustment Installation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 17. TheaterMaster Remote Control for Vision 140/150 MainControl Functions Disabled Navigating the Projector4x3 night Vhd 720p16x9 night Ltrbox nightAuto Source Locked Previous Channel Next Channel Name 16x9 nightNumber Sync 26.97 kHz Input 23.98 Hz Menu InterlaceSupport Native aspect ratio is with the primary lens only. With anSize and Position Menu Installation Adjust Pixel Tracking before Pixel Phase Picture Quality MenuWhite Balance There must be at least two consecutive white pixels present Uncheck this item before exiting this menuBack Porch Clipping Detector Color Enable Red Each settingInstallation Menu LumaCal lamp calibration takes approximately two minutesAbove, the Automatic Lens Calibration setting has no effect Working With the Lamp FactorsValue only 1246 may represent 3500 lumens, for example Easily maintained as the lamp ages RVRInstallation Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioInput Source Main MenuAspect Ratio 169 Aspect Ratio SettingsDescription Hdtv programs in theirRemote With a 2.351 screen and aPerform the adjustments in the order listed here PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationShould be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuCalibration ISF NightOperation You must enter a passcode to access the Service menu ServiceDo not change the Type setting in this menu Vertical Keystone Correction Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp and Filter Replacement Lamp cover 2 screwsRemoving the Lamp RVR Lens Replacement Removing the Primary LensTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Symptom Trigger CineWide withDescription General Vision 140/150 Error CodesLamp Failures Code Description Power and Cooling Code Description Code Description Miscellaneous Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Multiple serial commandsAspect Ratio Commands Image Preset Commands Output Shift Commands Value Stored? Description Miscellaneous Commands CommandEnter key Serial Communications Vision 140/150 Specifications Vision 140/150 SpecificationsPower Requirements Vision Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron
Top Page Image Contents