Allied Telesis AT-8500 Series manual Maximum

Page 53

AT-8500 Series Layer 2+ Fast Ethernet Switches Installation Guide

Table 11 contains the cabling specifications for the fiber optic ports on an AT-8516F/SC switch.

Table 11. Fiber Optic Cabling and Distances

 

 

 

Maximum

Model

Speed

Cable Type

Operating

 

 

 

Distance

 

 

 

 

 

 

 

 

AT-8516F/SC

100 Mbps

50/125 or 62.5/125

Full-duplex

 

 

micron (core/cladding)

mode: 2 km

 

 

multimode fiber optic

(1.25 mi)

 

 

cable

Half-duplex

 

 

 

mode: 412 m

 

 

 

(1,360 ft)

 

 

 

 

Note

For cabling specifications for an optional GBIC module, SFP module, expansion module, or stacking module, refer to the installation guide included with the option.

53

Image 53
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Page Figures Figures Tables Tables Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter OverviewModel Configuration Model ConfigurationsPort LEDs System LEDs Model DescriptionsShows the front and back panels of the AT-8524M switch Shows the front and back panels of the AT-8524POE switch Shows the front and back panels of the AT-8550GB switch AT-8550SP Switch Front and Back Panels 10/100Base-TX Twisted Pair Ports Port DescriptionsMaximum Distance 10/100/ 1000Base-T Twisted Pair Ports 100Base-FX Fiber Optic Ports Type of Cable Power Over Ethernet Minimum Power Maximum Power Class Gbic Module Gbic and SFP SlotsModule Expansion Slots State Description Twisted Pair Port LEDs LED Mode Select ButtonLEDs Mode FDX OFF Indicates that the port is operating at 10 or Fiber Optic Port LEDs Gbic and SFP Expansion Slot LEDs Maste RS-232 Terminal Port Power Options and Connectors AC Power Connector DC Power Connector MAC Address Table Duplex Mode Few Basics about Ethernet SwitchingBack Pressure and Flow Control Store ForwardOverview Collapsed Backbone Topology Power Workgroup TopologyNetwork Topologies Mixed Topology Mixed Topology Overview Installation Reviewing Safety Precautions Page Installation Selecting a Site for the Switch Model Speed Cable Type Planning the InstallationMaximum Maximum Unpacking the Switch Installing the Switch in a Rack Installation Page Removing the Expansion Slot Faceplate Installing an Optional Expansion or Stacking ModuleAT-A46 Installing an Optional Gbic Ferrules of the optical connector Bore Installing an Optional SFP Transceiver Page Cabling Twisted Pair Ports Cabling the SwitchCabling Fiber Optic Ports SC Port Transmitter Fiber Connector Cabling Expansion Modules Powering on an AC Powered Switch Page Positive, Ground, and Negative Terminals Wiring and Powering on an DC Powered Unit8mm ±1mm 31in. ±0.039in Installation Starting a Local Management Session Installation Warranty Registration Installation Twisted Pair Port Link LED is Off PWR LED is OffFiber Optic Port Link LED is Off Fault LED is On Continuously PoE Device is Not Receiving PowerCannot Establish a Local Management Session Appendix a Physical SpecificationsEnvironmental Specifications Safety and Electromagnetic Emissions Certifications Power SpecificationsSignal Pin MDI SignalPin MDI Signal MDI-X Signal RJ-45 Twisted Pair Port PinoutsUnused RX- and Vport-2 TX- and Vport-2 MDI Configuration MDI-X Configuration Pinout PairAT-8516F/SC Fiber Optic Port Specifications RS-232 Terminal Port Pinouts Pin SignalPin Definition RPS Connector Port PinoutsPin 3V RS13 3.3V RS+ Dual SC Type Connector