Allied Telesis AT-8500 Series manual Ferrules of the optical connector Bore

Page 61

AT-8500 Series Layer 2+ Fast Ethernet Switches Installation Guide

ferrules of the optical connector.

Ferrule

Bore

Figure 17. Optical Bore and Ferrule of GBIC Module

Note

Unnecessary removal and insertion of a GBIC can lead to premature failure.

4.Slide the GBIC module, with the label side up, into an expansion slot on the switch, as shown in Figure 18.

The GBIC can be installed in either slot. The GBIC module is seated in the slot when it clicks into place.

	49
	LINK
	50
	LINK
1000	BASE-X
	BASE-X
	UPLINK P
	ORTS

MODE	49R	LINK


10/100/1000BASE-T
MODE	50R	LINK

Figure 18. Installing a GBIC Module

5.If you purchased two GBIC modules for the switch, repeat this procedure to install the second module.

Note

Unnecessary removal and insertion of a GBIC can lead to premature failure.

61

Image 61

Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Page Figures Figures Tables Tables Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter OverviewModel Configuration Model ConfigurationsPort LEDs System LEDs Model DescriptionsShows the front and back panels of the AT-8524M switch Shows the front and back panels of the AT-8524POE switch Shows the front and back panels of the AT-8550GB switch AT-8550SP Switch Front and Back Panels 10/100Base-TX Twisted Pair Ports Port DescriptionsMaximum Distance 10/100/ 1000Base-T Twisted Pair Ports 100Base-FX Fiber Optic Ports Type of Cable Power Over Ethernet Minimum Power Maximum Power Class Gbic Module Gbic and SFP SlotsModule Expansion Slots LEDs Twisted Pair Port LEDs LED Mode Select ButtonState Description Mode FDX OFF Indicates that the port is operating at 10 or Fiber Optic Port LEDs Gbic and SFP Expansion Slot LEDs Maste RS-232 Terminal Port Power Options and Connectors AC Power Connector DC Power Connector MAC Address Table Duplex Mode Few Basics about Ethernet SwitchingBack Pressure and Flow Control Store ForwardOverview Network Topologies Power Workgroup TopologyCollapsed Backbone Topology Mixed Topology Mixed Topology Overview Installation Reviewing Safety Precautions Page Installation Selecting a Site for the Switch Maximum Planning the InstallationModel Speed Cable Type Maximum Unpacking the Switch Installing the Switch in a Rack Installation Page Removing the Expansion Slot Faceplate Installing an Optional Expansion or Stacking ModuleAT-A46 Installing an Optional Gbic Ferrules of the optical connector Bore Installing an Optional SFP Transceiver Page Cabling Twisted Pair Ports Cabling the SwitchCabling Fiber Optic Ports SC Port Transmitter Fiber Connector Cabling Expansion Modules Powering on an AC Powered Switch Page Positive, Ground, and Negative Terminals Wiring and Powering on an DC Powered Unit8mm ±1mm 31in. ±0.039in Installation Starting a Local Management Session Installation Warranty Registration Installation Twisted Pair Port Link LED is Off PWR LED is OffFiber Optic Port Link LED is Off Fault LED is On Continuously PoE Device is Not Receiving PowerCannot Establish a Local Management Session Environmental Specifications Physical SpecificationsAppendix a Safety and Electromagnetic Emissions Certifications Power SpecificationsSignal Pin MDI SignalPin MDI Signal MDI-X Signal RJ-45 Twisted Pair Port PinoutsUnused RX- and Vport-2 TX- and Vport-2 MDI Configuration MDI-X Configuration Pinout PairAT-8516F/SC Fiber Optic Port Specifications RS-232 Terminal Port Pinouts Pin SignalPin Definition RPS Connector Port PinoutsPin 3V RS13 3.3V RS+ Dual SC Type Connector