Allied Telesis AT-8500 Series manual AT-8516F/SC Fiber Optic Port Specifications

Page 85

AT-8500 Series Layer 2+ Fast Ethernet Switches Installation Guide

AT-8516F/SC Fiber Optic Port Specifications

Standard:	100Base-FX
Speed:	100 Mbps
Maximum Operating
Distance:	2 km (1.24 mi)
Connectors:
AT-8516F/SC	Dual SC Connector
Type of Cabling:	50/125 micron or 62.5/125 micron
	(core/cladding) multimode fiber optic
	cabling
Operating Wavelength:	1310 nm
Transmitter Output Power:
50/125 micron cabling
Minimum:	-22.5 dBm average
Maximum:	-14 dBm average
62.5/125 micron cabling
Minimum:	-19 dBm average
Maximum:	-14 dBm average
Receiver Sensitivity:
Minimum:	-31 dBm average
Maximum:	-14 dBm average

85

Image 85

Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Page Figures Figures Tables Tables Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter OverviewModel Configuration Model ConfigurationsPort LEDs System LEDs Model DescriptionsShows the front and back panels of the AT-8524M switch Shows the front and back panels of the AT-8524POE switch Shows the front and back panels of the AT-8550GB switch AT-8550SP Switch Front and Back Panels 10/100Base-TX Twisted Pair Ports Port DescriptionsMaximum Distance 10/100/ 1000Base-T Twisted Pair Ports 100Base-FX Fiber Optic Ports Type of Cable Power Over Ethernet Minimum Power Maximum Power Class Gbic Module Gbic and SFP SlotsModule Expansion Slots LEDs Twisted Pair Port LEDs LED Mode Select ButtonState Description Mode FDX OFF Indicates that the port is operating at 10 or Fiber Optic Port LEDs Gbic and SFP Expansion Slot LEDs Maste RS-232 Terminal Port Power Options and Connectors AC Power Connector DC Power Connector MAC Address Table Duplex Mode Few Basics about Ethernet SwitchingBack Pressure and Flow Control Store ForwardOverview Network Topologies Power Workgroup TopologyCollapsed Backbone Topology Mixed Topology Mixed Topology Overview Installation Reviewing Safety Precautions Page Installation Selecting a Site for the Switch Maximum Planning the InstallationModel Speed Cable Type Maximum Unpacking the Switch Installing the Switch in a Rack Installation Page Removing the Expansion Slot Faceplate Installing an Optional Expansion or Stacking ModuleAT-A46 Installing an Optional Gbic Ferrules of the optical connector Bore Installing an Optional SFP Transceiver Page Cabling Twisted Pair Ports Cabling the SwitchCabling Fiber Optic Ports SC Port Transmitter Fiber Connector Cabling Expansion Modules Powering on an AC Powered Switch Page Positive, Ground, and Negative Terminals Wiring and Powering on an DC Powered Unit8mm ±1mm 31in. ±0.039in Installation Starting a Local Management Session Installation Warranty Registration Installation Twisted Pair Port Link LED is Off PWR LED is OffFiber Optic Port Link LED is Off Fault LED is On Continuously PoE Device is Not Receiving PowerCannot Establish a Local Management Session Environmental Specifications Physical SpecificationsAppendix a Safety and Electromagnetic Emissions Certifications Power SpecificationsSignal Pin MDI SignalPin MDI Signal MDI-X Signal RJ-45 Twisted Pair Port PinoutsUnused RX- and Vport-2 TX- and Vport-2 MDI Configuration MDI-X Configuration Pinout PairAT-8516F/SC Fiber Optic Port Specifications RS-232 Terminal Port Pinouts Pin SignalPin Definition RPS Connector Port PinoutsPin 3V RS13 3.3V RS+ Dual SC Type Connector