Allied Telesis AT-8500 Series manual 3V RS, Pin

Page 88

Appendix A: Technical Specifications

Table 16. Pin Definitions of the 16-pin RPS Connector (Continued)

Pin

Definition

16 +3.3V DC Return

Figure 31 illustrates the pin layout to the RPS connector on the

AT-8524POE switch.

A2

7

1

A1

15 8

Figure 31. AT-8524POE RPS Connector Pin Layout

Table 17 lists the RPS connector pins and definitions.

Table 17. Pin Definitions for the RPS Connector on the AT-8524POE

Switch

Pin

Definition

 

 

 

 

A1

48V Return

 

 

A2

Return

 

 

1

48V

 

 

2

48V RS+

 

 

3

Redundant Power Supply (RPS) present

 

 

4

12V RS-

 

 

5

12V RS+

 

 

6

12V

 

 

7

3.3V

 

 

8

48V

 

 

9

48V

 

 

10

48V RS-

 

 

11

RPS GOOD

 

 

12

3.3V RS-

 

 

88

Image 88
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Page Figures Figures Tables Tables Preface Safety Symbols Used in this Document Symbol Meaning DescriptionWhere to Find Web-based Guides Management Software Updates Contacting Allied TelesisOverview ChapterModel Configurations Model ConfigurationModel Descriptions Port LEDs System LEDsShows the front and back panels of the AT-8524M switch Shows the front and back panels of the AT-8524POE switch Shows the front and back panels of the AT-8550GB switch AT-8550SP Switch Front and Back Panels Port Descriptions 10/100Base-TX Twisted Pair PortsMaximum Distance 10/100/ 1000Base-T Twisted Pair Ports 100Base-FX Fiber Optic Ports Type of Cable Power Over Ethernet Minimum Power Maximum Power Class Gbic and SFP Slots Gbic ModuleModule Expansion Slots LEDs Twisted Pair Port LEDs LED Mode Select ButtonState Description Mode FDX OFF Indicates that the port is operating at 10 or Fiber Optic Port LEDs Gbic and SFP Expansion Slot LEDs Maste RS-232 Terminal Port Power Options and Connectors AC Power Connector DC Power Connector Few Basics about Ethernet Switching MAC Address Table Duplex ModeStore Forward Back Pressure and Flow ControlOverview Network Topologies Power Workgroup TopologyCollapsed Backbone Topology Mixed Topology Mixed Topology Overview Installation Reviewing Safety Precautions Page Installation Selecting a Site for the Switch Maximum Planning the InstallationModel Speed Cable Type Maximum Unpacking the Switch Installing the Switch in a Rack Installation Page Installing an Optional Expansion or Stacking Module Removing the Expansion Slot FaceplateAT-A46 Installing an Optional Gbic Ferrules of the optical connector Bore Installing an Optional SFP Transceiver Page Cabling the Switch Cabling Twisted Pair PortsCabling Fiber Optic Ports SC Port Transmitter Fiber Connector Cabling Expansion Modules Powering on an AC Powered Switch Page Wiring and Powering on an DC Powered Unit Positive, Ground, and Negative Terminals8mm ±1mm 31in. ±0.039in Installation Starting a Local Management Session Installation Warranty Registration Installation PWR LED is Off Twisted Pair Port Link LED is OffFiber Optic Port Link LED is Off PoE Device is Not Receiving Power Fault LED is On ContinuouslyCannot Establish a Local Management Session Environmental Specifications Physical SpecificationsAppendix a Power Specifications Safety and Electromagnetic Emissions CertificationsPin MDI Signal SignalPin MDI Signal MDI-X Signal RJ-45 Twisted Pair Port PinoutsMDI Configuration MDI-X Configuration Pinout Pair Unused RX- and Vport-2 TX- and Vport-2AT-8516F/SC Fiber Optic Port Specifications Pin Signal RS-232 Terminal Port PinoutsRPS Connector Port Pinouts Pin Definition3V RS Pin13 3.3V RS+ Dual SC Type Connector