TDK 5KW Dvc?, Filter?, Out?, Fld?, Fbd ?, Fbdrst, Ovp?, Ovm, Uvl?, Ast?, Sav, Rcl

#	Command		Description
		Display Voltage and Current data. Data will be returned as a string of ASCII
		characters. A comma will separate the different fields. The fields, in order, are:
7	DVC?	Measured Voltage, Programmed Voltage, Measured Current, Programmed Cur-
		rent, Over Voltage Set Point and Under Voltage Set Point.
		Example: 5.9999,6.0000,010.02,010.00,7.500,0.000
8	FILTER	Set the low pass filter frequency of the A to D Converter for Voltage and Current
	nn	Measurement where nn = 18, 23 or 46.
9	FILTER?	Returns the A to D Converter filter frequency: 18,23 or 46 Hz.
		Turns the output to ON or OFF. Recover from Safe-Start, OVP or FLD fault.
10	OUT n	OUT 1 (or OUT ON)-Turn On.
		OUT 0 (or OUT OFF)-Turn Off
11	OUT?	Returns the output On/Off status string.
		ON - output On. OFF - output Off.
12	FLD n	Sets the Foldback protection to ON or OFF.
		FLD 1 (or FOLD ON) - Arms the Foldback protection
		FLD 0 (or FOLD OFF) - Cancels the Foldback protection.
		When the Foldback protection has been activated, OUT 1 command will release
		the protection and re-arm it, while FLD 0 will cancel the protection.
13	FLD?	Returns the Foldback protection status string:
		“ON” - Foldback is armed. “OFF” - Foldback is cancelled.
14	FBD nn	Add (nn x 0.1) seconds to the Fold Back Delay. This delay is in addition to the
		standard delay. The range of nn is 0 to 255. The value is stored in eprom at AC
		power down and recovered at AC power up.
15	FBD ?	Supply returns the value of the added Fold Back Delay.
16	FBDRST	Reset the added Fold Back Delay to zero.
		Sets the OVP level. The OVP setting range is given in Table 7-7. The number of
		characters after OVP is up to 12. The minimum setting level is approximately
17	OVP n	105% of the Output Voltage setting, or the value in Table 7-7, whichever is
		higher. The maximum OVP setting level is shown in Table 5-1. Attempting to
		program the OVP below this level will result in an execution error response
		(“E04”). The OVP setting stays unchanged.
18	OVP?	Returns the setting “n” where “n” is the exact string in the user’s “OVP n”. When
		in Local mode, returns the last setting from the front panel in a 4 digit string.
19	OVM	Sets OVP level to the maximum level. Refer to Table 7-7.
20	UVL n	Sets Under Voltage Limit. Value of “n” may be equal to PV setting, but returns
		“E06” if higher. Refer to Table 7-8 for UVL programming range.
21	UVL?	Returns the setting “n” where “n” is the exact string in the user’s “UVL n”. When
		in Local mode, returns the last setting from the front panel in a 4 digit string.
		Sets the Auto-restart mode to ON or OFF.
22	AST n	AST 1 (or AST ON): Auto restart On.
		AST 0 (or AST OFF): Auto restart Off.
23	AST?	Returns the string auto-restart mode status.
24	SAV	Saves present settings. The settings are the same as power-down last setting.
		These settings are erased when the supply power is switched Off and the new
		“last settings” are saved.
25	RCL	Recalls	last settings. Settings are from the last power-down or from the last
		“SAV”	command.
			57

83-515-000 Rev. B