TDK 5KW Enain, Ifcom, Local, Remote, Vpgm, Ipgm, Vmon, Com, Cv/Cc, Enaout, Psok, Loc/Rem, Signal

Page 42

J1

Signal

 

 

contact

name

Function

Reference

J1-1

ENA_IN

Enable/Disable the power supply output by dry-contact

Sec. 5.8

 

 

(short/open) with ENA_OUT.

 

J1-2

IF_COM

Isolated Interface Common. Return for the SO control,

Sec.5.7, 5.10

J1-3

 

PS_OK signal and for the optional IEEE interface.

 

J1-47

N/C

No Connection

 

J1-8

LOCAL/

Input for selecting between Local or Remote analog pro-

Sec. 6.2

 

REMOTE

gramming of Output Voltage and Output Current.

 

J1-9

VPGM

Input for remote analog voltage/resistance programming

Sec. 6.16.4

 

 

of the Output Voltage.

 

J1-10

IPGM

Input for remote analog voltage/resistance programming

Sec. 6.16.4

 

 

of the Output Current.

 

J1-11

VMON

Output for monitoring the power supply Output Voltage.

Sec. 6.6

J1-12

COM

Control Common. Return for VMON, IMON, CV/CC,

 

 

 

LOC/REM.

 

 

 

Connected internally to the negative sense potential (-S).

 

J1-13

CV/CC

Output for Constant-Voltage/Constant-Current mode

Sec. 5.9

 

 

indication.

 

J1-14

ENA_OUT

Enable/Disable the power supply output by dry-contact

Sec. 5.8

 

 

(short/open) with ENA_IN.

 

J1-15

SO

Input for Shut-Off control of the power supply output.

Sec. 5.7

J1-16

PS_OK

Output for indication of the power supply status.

Sec. 5.10

J1-1720

N/C

No Connection.

 

J1-21

LOC/REM

Output for indicating if the unit is in Local or Remote

Sec. 6.3

 

SIGNAL

analog programming mode.

 

J1-22

VPGM_RTN

Return for VPGM input. Connected internally to the “-S”.

Sec. 6.1, 6.4,

 

 

 

6.5

J1-23

IPGM_RTN

Return for IPGM input. Connected internally to the “-S”.

Sec. 6.1, 6.4,

 

 

 

6.5

J1-24

IMON

Output for monitoring the power supply Output Current.

Sec. 6.6

J1-25

P

Output for current balance in parallel operation.

Sec. 5.15

34

83-515-000 Rev. B

Page 41 Page 43
Image 42
Page 41 Page 43
Contents 2U Genesystm 5kW Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and Connectors ……………… Remote Analog PROGRAMMING……………………………………………… Isolated Analog Progamming OPTION………………………………… Disclaimer Limitation of WarrantyWarranty Service Trademark InformationSafety Instructions Environmental Conditions FCC Compliance NoticeSICHERHEITS-INSTALLATIONS Anweisungen SICHERHEITS-HINWEISE Sicherheits-und WarnsymboleAnderungen and Bauteileersatz UmweltbedingungenIntroduction Features and optionsGeneral Information General DescriptionAnalog voltage programming and monitoring Multiple output power systemControl via the serial communication port Parallel operationAccessories Specifications 83-515-000 Rev. B Supplemental Characteristics Genesystm 5000W Power Supplies Outline Drawings Preparation for USE InstallationGeneral Initial InspectionsLOCATION, Mounting and Cooling To install the Power Supply in a rackRack Mounting AC Source RequirementsAC Input Wire Connection AC Input Power ConnectionAC Input Connector AC Input CordStripped Wires installed in Strain Relief Constant Voltage Check TURN-ON Checkout ProcedurePrior to Operation Constant Current CheckUVL Check Address SettingBaud Rate Setting RS-232 and RS-485 only Foldback CheckCurrent Carrying Capacity Connecting the LoadLoad Wiring AWGWire termination Noise and Impedance EffectsInductive loads Making the load connections 8V to 100V Models Load wires connection, 8V to 100V models 83-515-000 Rev. B Connecting single loads, local sensing default Connecting single loads, remote sensingConnecting multiple loads, radial distribution method Multiple load connection with distribution terminals Grounding outputsOutput Terminal Grounding Sense wiringLocal and Remote Sensing Local sensing10.4 J2 sense connector technical information Remote sensingRepackaging for Shipment Front and Rear Panel Controls and Connectors Front Panel Controls and IndicatorsSection Rear Panel Connections and Controls Rear Panel SW1 Setup Switch SW1 setup DIP-switchResetting the SW1 switch 1 SW1 position functionRear Panel J1 Programming and Monitoring Connector Making J1 connectionsIfcom SignalEnain LocalLocal Operation Constant Voltage ModeConstant Current Mode IntroductionAutomatic Crossover Setting the OVP levelResetting the OVP circuit Over Voltage Protection OVPFoldback Protection Output SHUT-OFF SO Control VIA Rear Panel J1 Connector4A Under Voltage Limit UVL Output ON/OFF ControlENABLE/DISABLE Control VIA Rear Panel J1 Connector CV/CC SignalPsok Signal SAFE-START and AUTO-RESTART Modes Over Temperature Protecton OTPLast Setting Memory Series OperationSeries connection for increased output voltage Series connection, local sensingSeries connection for positive and negative output voltage Series connection for positive/negative output voltagesParallel Operation Master and Slave units default operation Advanced parallel configurationSetting the units as Master or Slave Connection to the loadTo release units from Slave mode Current display accuracyAST OFF *OUT OFF Unlocked front panel DAISY-CHAIN ConnectionFront Panel Locking Locked front panelRemote Analog Programming LOCAL/REMOTE Analog ControlLOCAL/REMOTE Analog Indication J1 connector, rear panel view Resisitive Programming of Output Voltage and Current Limit Remote resistive programmingRemote Monitoring of Output Voltage and Current RS232 & RS485 Remote Control ConfigurationRear Panel RS232/RS485 Connector 6 RS232/RS485 port in Local modeFront panel in Remote mode MD Mode SRQ MD Mode DescriptionMD Mode enable Serial communication mode MD Mode SRQ RetransmissionConnecting Power Supplies to RS232 or RS485 BUS Single power supplyCommunication Interface Protocol Error Messages Command SET DescriptionInitialization Control Commands ID Control CommandsOutput Control Commands FILTER? DVC?Filter OUT?Global Output Commands GeneralDisable SRQ retransmission MD Mode Option Required Single Byte CommandsEnable MD Mode MD Mode Option Required Enable SRQ retransmission MD Mode Option RequiredTest if MD Mode is Installed Addressed commands with response Read registersPrint Power On Time Addressed commands without response Acknowledge SRQ1010 None Disable retransmission of SRQs by sup Voltage programming range STATUS, Error and SRQ Registers Status Control CommandsConditional Registers Status RegistersBIT FoldService Request Enable and Event Registers Fault Enable RegisterFault Event Register Status Enable Register Status Event RegisterPower supply set-up Serial Communication Test SET-UPCommunication Test 1 0-5V/0-10V Option PN IS510 SpecificationsIsolated Analog Programming Option PPM/CIsolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance Fuse Rating OUP

5KW specifications

The TDK 5KW is a cutting-edge power supply solution designed to deliver high performance and efficiency in a compact form. This robust unit is engineered for various applications, including industrial automation, telecommunications, and renewable energy systems. With a focus on reliability and durability, the TDK 5KW is an excellent choice for users seeking a dependable power source.

One of the standout features of the TDK 5KW is its advanced power conversion technology. It utilizes a high-frequency switching technique that allows for superior efficiency, minimizing energy loss and reducing heat generation. By operating at high efficiency levels, the TDK 5KW helps lower operational costs while contributing to a greener environment.

The power supply is equipped with a wide input voltage range, making it suitable for global applications. It can accept input voltages from 90 to 264 VAC, ensuring versatility and compatibility with various electrical systems. This feature also enhances its usability in different geographic regions without the need for additional transformers or converters.

Another significant characteristic of the TDK 5KW is its modular design, which allows for easy integration into existing systems. The power supply features a compact footprint, making it ideal for installations where space is at a premium. Moreover, its robust construction ensures that it can withstand harsh operating conditions, including extreme temperatures and vibrations.

Reliability is further enhanced through built-in protection features, including overvoltage, overcurrent, and short-circuit protection. These safety mechanisms not only safeguard the power supply itself but also protect the connected equipment from damage, making it a trustworthy choice for critical applications.

The TDK 5KW also supports various communication protocols, enabling seamless integration into modern automation systems. This feature allows for real-time monitoring and control, providing users with essential data to optimize performance and troubleshoot issues efficiently.

In summary, the TDK 5KW is a powerful, efficient, and reliable power supply solution that caters to a broad range of applications. Its advanced technologies, modular design, and robust safety features make it an essential component for anyone looking to enhance their electrical systems with a high-quality power source.
Top Page Image Contents