SUPER MICRO Computer X6QT8, X6QTE+ user manual Empty socket, Processor installed

Page 27

Chapter 2: Installation

Figure 2-1. PGA604 Socket: Empty and with Processor Installed

Empty socket

!

Warning! Make

sure that you lift the lever completely when installing the CPU; otherwise, damage to the socket or CPU may occur.

Lever

Triangle

(Pin 1)

Processor (installed)

Triangle

(Pin 1)

(*Note: The CPU shown in the picture is for display only. Your CPU may or may not look exactly the same as the one shown in the picture above.)

Mounting the Motherboard in the Chassis

All motherboards have standard mounting holes to ﬁ t different types of chassis. Make sure that the locations of all the mounting holes for both the motherboard and the chassis match. Make sure that the metal standoffs click in or are screwed in tightly. Then use a screwdriver to secure the motherboard onto the motherboard tray. Please note that some components are very close to the mounting holes. Take caution when installing or removing these components to prevent damage to the components.

2-5

Image 27

Contents Super Page Conventions Used in this Manual About This ManualTable of Contents Table of Contents Troubleshooting BiosAppendices Overview ChecklistAsia-Paciﬁc Contacting SupermicroHeadquarters EuropeX6QT8 Image Important Notes to the UserSuper X6QT8 Jumper Description Default Setting Quick Reference X6QT8Description LED Indicator Description Super Quick Reference X6QTE+ Expansion Slots *See Note 3 on Motherboard FeaturesMemory ChipsetSoftware Acpi Power FeaturesLED Indicators DimensionsBlock Diagram of the E8501 Chipset Interfaces Chipset OverviewE8501 Chipset Independent Memory InterfacePC Health Monitoring Special FeaturesThermal Management/CPU VRM Overheat Acpi FeaturesAuto-Switching Voltage Regulator for the CPU Core Slow Blinking LED for Suspend-State IndicatorWake-On-LAN WOL Power SupplyMain Switch Override Mechanism External Modem Ring-On WORSuper I/O Precautions Static-Sensitive DevicesUnpacking CPU Installation Processor and Heatsink InstallationHeatsink Installation To Un-install the Heatsink Processor installed Empty socketMounting the Motherboard in the Chassis Installing DIMMs Dimm Installation See FigureMemory Support Back Panel Connectors/IO Ports Control Panel Connectors/IO PortsFront Control Panel JF1 Header PinsFront Control Panel Pin Deﬁnitions NMI Button Power LEDHDD LED NIC1/NIC2 LED IndicatorsPower Fail LED Overheat/Fan Fail LEDOH/Fan Fail LED PWR Fail LED Reset Button Power ButtonReset PWR Button Pin PWR Connecting CablesATX Power Connector Secondary Power ConnectorsUniversal Serial Bus USB Chassis IntrusionWake-On-Ring Wake-On-LANGlan Giga-bit Ethernet Ports Serial PortsFan Headers ATX PS/2 Keyboard and PS/2 Mouse PortsVGA Connector Power Supply FailurePWR Supply Fail Connector SMB Power I2 CSMB Header Compact Flash Card PWR Connectors JWF1, JWF2 Power LED/Speaker JD1Alarm Reset JAR1 Jtag ConnectorJumper Settings Glan Ports Enable/DisableExplanation Jumpers Watch Dog Cmos ClearFSB Speed Select VGA Enable/DisableScsi Termination Enable/ Disable *For X6QT8 only Scsi Controller Enable/ Disable *For X6QT8 only3rd PWR Fail Detect 3rd PWR Supply PWR Failure Detect JP13LeftRight Onboard IndicatorsGlan LEDs Overheat LED JOH1Scsi Channel Indicators DA1, DA2 *X6QT8 only Onboard Power LED LE1DA1 DA2 LE1 Floppy Connector Floppy, IPMI, Hard Disk Drive and Scsi ConnectionsFloppy IDE Drive Connectors Pin Deﬁnitions IDE IDE ConnectorsIpmi 2.0 Socket Ultra320 Scsi ConnectorsInstallation X6QT8 OnlyPage Losing the System’s Setup Conﬁguration Troubleshooting ProceduresBefore Power On No PowerMemory Errors Technical Support ProceduresFrequently Asked Questions Returning Merchandise for Service How To Change the Conﬁguration Data Starting the Setup UtilityIntroduction System Time/System Date Main SetupProcessors System MemoryAdvanced Settings Conﬁgure Advanced CPU SettingsCPU Conﬁguration Sub-Menu Max Cpuid Value Limit Hyper-Threading TechnologyIntel R C-State Technology IDE Conﬁguration Sub-Menu A.R.T. For Hard disk drives DMA ModePCI/PnP Conﬁguration Floppy ConﬁgurationSuper IO Conﬁguration Submenu Advanced Chipset Settings Event Log Conﬁguration Apci ConﬁgurationVoltage Temperatures CPU Overheat TemperatureHardware Health Conﬁguration Fan SpeedMPS Revision Active State Power ManagementMPS Conﬁguration PCI Express ConﬁgurationRemote Access Conﬁguration Smbios ConﬁgurationUSB Conﬁguration Interrupt 19 Capture Bios Settings ConﬁgurationResume On Modem Ring Boot SettingsWatch Dog Timer Restore on AC Power LossCD/DVD Drives Boot Device PriorityHard Disk Drives Removable DrivesSecurity Settings Discarding Changes and Exit Load Optimal DefaultsExit Options Saving Changes and ExitLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesX6QT8/X6QTE+ User’s Manual D0h D1h D3h D4h D5h Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page ATA Operate Mode Combined ModeIntroduction to the Intel ICH5R I/O Controller Hub Adaptec Embedded Serial ATA with HostRAID Controller Driver Using the Array Conﬁguration Utility ACU Using the Adaptec RAID Conﬁguration Utility ARCManaging Arrays Deleting Arrays Viewing Array PropertiesFrom the ARC menu, select Array Conﬁguration Utility ACU EnterTo create an array Creating ArraysAssigning Array Properties Raid Level Create Via When Appropriate When you are ﬁ nished, press Done as the screen shown below Adding a Bootable Array Deleting a Bootable ArrayCtrl+B To initialize drives Initializing Disk DrivesPage Page To Rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesPage To Exit Adaptec RAID Conﬁguration Utility You can choose from the following optionsInstalling Intels ICH5R Driver by Adaptec and the Windows OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control