SUPER MICRO Computer X6QTE+, X6QT8 user manual Boot Settings, Watch Dog Timer, Resume On Modem Ring

Page 74

X6QT8/X6QTE+ User’s Manual

Watch Dog Timer

If enabled, this option will automatically reset the system if the system is not active for more than 5 minutes. The options are Enabled and Disabled.

Resume On Modem Ring

Select On to “wake your system up” when an incoming call is received by your modem. The options are On and Off.

Restore on AC Power Loss

The feature allows the user to set the power state after a power outage. Select Power-Off for the system power to remain off after a power loss. Select Power-On for the system power to be turned on after a power loss. Select Last State to allow the system to resume its last state before the power loss. The options are Power- On, Power-Off and Last State.

4-4 Boot Settings

This feature allows the user to confi gure the following items:

4-16

Image 74
Contents Super Page About This Manual Conventions Used in this ManualTable of Contents Table of Contents Appendices TroubleshootingBios Checklist OverviewEurope Contacting SupermicroHeadquarters Asia-PacificImportant Notes to the User X6QT8 ImageSuper X6QT8 Description Jumper Description Default SettingQuick Reference X6QT8 LED Indicator Description Super Quick Reference X6QTE+ Chipset Motherboard FeaturesMemory Expansion Slots *See Note 3 onDimensions Acpi Power FeaturesLED Indicators SoftwareBlock Diagram of the E8501 Chipset Independent Memory Interface Chipset OverviewE8501 Chipset InterfacesSpecial Features PC Health MonitoringSlow Blinking LED for Suspend-State Indicator Acpi FeaturesAuto-Switching Voltage Regulator for the CPU Core Thermal Management/CPU VRM OverheatExternal Modem Ring-On WOR Power SupplyMain Switch Override Mechanism Wake-On-LAN WOLSuper I/O Unpacking PrecautionsStatic-Sensitive Devices Processor and Heatsink Installation CPU InstallationHeatsink Installation To Un-install the Heatsink Mounting the Motherboard in the Chassis Processor installedEmpty socket Memory Support Installing DIMMsDimm Installation See Figure Control Panel Connectors/IO Ports Back Panel Connectors/IO PortsJF1 Header Pins Front Control PanelPower LED Front Control Panel Pin Definitions NMI ButtonNIC1/NIC2 LED Indicators HDD LEDOH/Fan Fail LED PWR Fail LED Power Fail LEDOverheat/Fan Fail LED Reset PWR Button Reset ButtonPower Button Secondary Power Connectors Connecting CablesATX Power Connector Pin PWRChassis Intrusion Universal Serial Bus USBWake-On-LAN Wake-On-RingSerial Ports Glan Giga-bit Ethernet PortsATX PS/2 Keyboard and PS/2 Mouse Ports Fan HeadersPWR Supply Fail VGA ConnectorPower Supply Failure SMB Header ConnectorSMB Power I2 C Power LED/Speaker JD1 Compact Flash Card PWR Connectors JWF1, JWF2Jtag Connector Alarm Reset JAR1Explanation Jumpers Jumper SettingsGlan Ports Enable/Disable Cmos Clear Watch DogVGA Enable/Disable FSB Speed SelectScsi Controller Enable/ Disable *For X6QT8 only Scsi Termination Enable/ Disable *For X6QT8 only3rd PWR Supply PWR Failure Detect JP13 3rd PWR Fail DetectOverheat LED JOH1 Onboard IndicatorsGlan LEDs LeftRightDA1 DA2 LE1 Scsi Channel Indicators DA1, DA2 *X6QT8 onlyOnboard Power LED LE1 Floppy Floppy ConnectorFloppy, IPMI, Hard Disk Drive and Scsi Connections IDE Connectors IDE Drive Connectors Pin Definitions IDEX6QT8 Only Ultra320 Scsi ConnectorsInstallation Ipmi 2.0 SocketPage No Power Troubleshooting ProceduresBefore Power On Losing the System’s Setup ConfigurationTechnical Support Procedures Memory ErrorsFrequently Asked Questions Returning Merchandise for Service Introduction How To Change the Configuration DataStarting the Setup Utility System Memory Main SetupProcessors System Time/System DateCPU Configuration Sub-Menu Advanced SettingsConfigure Advanced CPU Settings Intel R C-State Technology Max Cpuid Value LimitHyper-Threading Technology IDE Configuration Sub-Menu DMA Mode A.R.T. For Hard disk drivesFloppy Configuration PCI/PnP ConfigurationSuper IO Configuration Submenu Advanced Chipset Settings Apci Configuration Event Log ConfigurationFan Speed Temperatures CPU Overheat TemperatureHardware Health Configuration VoltagePCI Express Configuration Active State Power ManagementMPS Configuration MPS Revision Smbios Configuration Remote Access ConfigurationUSB Configuration Bios Settings Configuration Interrupt 19 CaptureRestore on AC Power Loss Boot SettingsWatch Dog Timer Resume On Modem RingRemovable Drives Boot Device PriorityHard Disk Drives CD/DVD DrivesSecurity Settings Saving Changes and Exit Load Optimal DefaultsExit Options Discarding Changes and ExitLoad Fail-Safe Defaults Appendix a Bios Error Beep Codes Beep Code Error Message DescriptionX6QT8/X6QTE+ User’s Manual Uncompressed Initialization Codes D0h D1h D3h D4h D5hBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Introduction to the Intel ICH5R I/O Controller Hub ATA Operate ModeCombined Mode Adaptec Embedded Serial ATA with HostRAID Controller Driver Using the Adaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACUManaging Arrays Enter Viewing Array PropertiesFrom the ARC menu, select Array Configuration Utility ACU Deleting ArraysCreating Arrays To create an arrayAssigning Array Properties Raid Level Create Via When Appropriate When you are fi nished, press Done as the screen shown below Ctrl+B Adding a Bootable ArrayDeleting a Bootable Array Initializing Disk Drives To initialize drivesPage Page Rebuilding Arrays To Rebuild an arrayUsing the Disk Utilities To access the disk utilitiesPage You can choose from the following options To Exit Adaptec RAID Configuration UtilityInstalling Intels ICH5R Driver by Adaptec and the Windows OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control