SUPER MICRO Computer X6QT8, X6QTE+ user manual About This Manual, Conventions Used in this Manual

Page 3
Manual Organization

Preface

Preface

About This Manual

This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the

X6QT8/X6QTE+ motherboard. The X6QT8/X6QTE+ supports single, dual or quad 64-bit Intel® Xeon processor MP, 7000 Series and 7100 Series processors at a front side bus speed of 800 or 677 MHz. Based upon the 64-bit Intel Xeon

MP/7000 Series/7100 Series processors, the X6QT8/X6QTE+ supports the dual system bus architecture, and allows for symmetric multiprocessing across two shared system bus interfaces, providing performance enhancement with increased bus speeds and bandwidth. This motherboard is especially designed for the 4-way server platform, and can be used in front-end, back-end, general- purpose, communication and storage market segments. Please refer to our web site (http://www.supermicro.com/products/motherboard/) for updates on supported processors. This product is intended to be professionally￿ installed.

Chapter 1 describes the features, specifi cations and performance of the mother- board and provides detailed information about the chipset.

Chapter 2 provides hardware installation instructions. Read this chapter when installing the processor, memory modules and other hardware components into the system.

Chapter 3 describes troubleshooting procedures for the video, the memory and the system setup stored in CMOS.

Chapter 4 includes an introduction to BIOS and provides detailed information on running the CMOS Setup utility.

Appendix A provides BIOS POST Messages.

Appendix B lists BIOS POST Codes.

Appendix C lists Software Installation Instructions.

Conventions Used in this Manual

Special attention should be given to the following symbols for proper installation and to prevent damage done to the components or injury to yourself:

Danger/Caution: Instructions to be strictly followed to prevent catastrophic system failure or to avoid bodily injury.

Warning: Important information given to ensure proper system installation or to prevent damage to the components.

Note: Additional Information given to differentiate various models or to ensure correct system setup.

iii

Image 3
Contents Super Page Conventions Used in this Manual About This ManualTable of Contents Table of Contents Troubleshooting BiosAppendices Overview ChecklistAsia-Pacific Contacting SupermicroHeadquarters EuropeX6QT8 Image Important Notes to the UserSuper X6QT8 Jumper Description Default Setting Quick Reference X6QT8Description LED Indicator Description Super Quick Reference X6QTE+ Expansion Slots *See Note 3 on Motherboard FeaturesMemory ChipsetSoftware Acpi Power FeaturesLED Indicators DimensionsBlock Diagram of the E8501 Chipset Interfaces Chipset OverviewE8501 Chipset Independent Memory InterfacePC Health Monitoring Special FeaturesThermal Management/CPU VRM Overheat Acpi FeaturesAuto-Switching Voltage Regulator for the CPU Core Slow Blinking LED for Suspend-State IndicatorWake-On-LAN WOL Power SupplyMain Switch Override Mechanism External Modem Ring-On WORSuper I/O Precautions Static-Sensitive DevicesUnpacking CPU Installation Processor and Heatsink InstallationHeatsink Installation To Un-install the Heatsink Processor installed Empty socketMounting the Motherboard in the Chassis Installing DIMMs Dimm Installation See FigureMemory Support Back Panel Connectors/IO Ports Control Panel Connectors/IO PortsFront Control Panel JF1 Header PinsFront Control Panel Pin Definitions NMI Button Power LEDHDD LED NIC1/NIC2 LED IndicatorsPower Fail LED Overheat/Fan Fail LEDOH/Fan Fail LED PWR Fail LED Reset Button Power ButtonReset PWR Button Pin PWR Connecting CablesATX Power Connector Secondary Power ConnectorsUniversal Serial Bus USB Chassis IntrusionWake-On-Ring Wake-On-LANGlan Giga-bit Ethernet Ports Serial PortsFan Headers ATX PS/2 Keyboard and PS/2 Mouse PortsVGA Connector Power Supply FailurePWR Supply Fail Connector SMB Power I2 CSMB Header Compact Flash Card PWR Connectors JWF1, JWF2 Power LED/Speaker JD1Alarm Reset JAR1 Jtag ConnectorJumper Settings Glan Ports Enable/DisableExplanation Jumpers Watch Dog Cmos ClearFSB Speed Select VGA Enable/DisableScsi Termination Enable/ Disable *For X6QT8 only Scsi Controller Enable/ Disable *For X6QT8 only3rd PWR Fail Detect 3rd PWR Supply PWR Failure Detect JP13LeftRight Onboard IndicatorsGlan LEDs Overheat LED JOH1Scsi Channel Indicators DA1, DA2 *X6QT8 only Onboard Power LED LE1DA1 DA2 LE1 Floppy Connector Floppy, IPMI, Hard Disk Drive and Scsi ConnectionsFloppy IDE Drive Connectors Pin Definitions IDE IDE ConnectorsIpmi 2.0 Socket Ultra320 Scsi ConnectorsInstallation X6QT8 OnlyPage Losing the System’s Setup Configuration Troubleshooting ProceduresBefore Power On No PowerMemory Errors Technical Support ProceduresFrequently Asked Questions Returning Merchandise for Service How To Change the Configuration Data Starting the Setup UtilityIntroduction System Time/System Date Main SetupProcessors System MemoryAdvanced Settings Configure Advanced CPU SettingsCPU Configuration Sub-Menu Max Cpuid Value Limit Hyper-Threading TechnologyIntel R C-State Technology IDE Configuration Sub-Menu A.R.T. For Hard disk drives DMA ModePCI/PnP Configuration Floppy ConfigurationSuper IO Configuration Submenu Advanced Chipset Settings Event Log Configuration Apci ConfigurationVoltage Temperatures CPU Overheat TemperatureHardware Health Configuration Fan SpeedMPS Revision Active State Power ManagementMPS Configuration PCI Express ConfigurationRemote Access Configuration Smbios ConfigurationUSB Configuration Interrupt 19 Capture Bios Settings ConfigurationResume On Modem Ring Boot SettingsWatch Dog Timer Restore on AC Power LossCD/DVD Drives Boot Device PriorityHard Disk Drives Removable DrivesSecurity Settings Discarding Changes and Exit Load Optimal DefaultsExit Options Saving Changes and ExitLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesX6QT8/X6QTE+ User’s Manual D0h D1h D3h D4h D5h Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page ATA Operate Mode Combined ModeIntroduction to the Intel ICH5R I/O Controller Hub Adaptec Embedded Serial ATA with HostRAID Controller Driver Using the Array Configuration Utility ACU Using the Adaptec RAID Configuration Utility ARCManaging Arrays Deleting Arrays Viewing Array PropertiesFrom the ARC menu, select Array Configuration Utility ACU EnterTo create an array Creating ArraysAssigning Array Properties Raid Level Create Via When Appropriate When you are fi nished, press Done as the screen shown below Adding a Bootable Array Deleting a Bootable ArrayCtrl+B To initialize drives Initializing Disk DrivesPage Page To Rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesPage To Exit Adaptec RAID Configuration Utility You can choose from the following optionsInstalling Intels ICH5R Driver by Adaptec and the Windows OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control