SUPER MICRO Computer X6QTE+, X6QT8 user manual Security Settings

Page 76

X6QT8/X6QTE+ User’s Manual

4-5 Security Settings

The AMI BIOS provides a Supervisor and a User password. If you use both pass- words, the Supervisor password must be set fi rst.

Change Supervisor Password

Select this option and press <Enter> to access the sub-menu, and then type in the password.

Change User Password

Select this option and press <Enter> to access the sub-menu, and then type in the password.

Clear User Password

This option allows the user to clear a password that has been previously entered into the system.

Password Check

Set to Setup to allow the system to perform a password check when the BIOS Setup is invoked. Set to Always to allow the system to perform a password check when the BIOS Setup is invoked or when the system boots up.

Boot Sector Virus Protection

This option is near the bottom of the Security Setup screen. Select "Disabled" to deactivate the Boot Sector Virus Protection. Select "Enabled" to enable boot sector protection. When Enabled, the AMIBOIS displays a warning when any program (or virus) issues a Disk Format command or attempts to write to the boot sector of the hard disk drive. The options are Enabled and Disabled.

4-18

Image 76
Contents Super Page About This Manual Conventions Used in this ManualTable of Contents Table of Contents Bios TroubleshootingAppendices Checklist OverviewContacting Supermicro HeadquartersEurope Asia-PacificImportant Notes to the User X6QT8 ImageSuper X6QT8 Quick Reference X6QT8 Jumper Description Default SettingDescription LED Indicator Description Super Quick Reference X6QTE+ Motherboard Features MemoryChipset Expansion Slots *See Note 3 onAcpi Power Features LED IndicatorsDimensions SoftwareBlock Diagram of the E8501 Chipset Chipset Overview E8501 ChipsetIndependent Memory Interface InterfacesSpecial Features PC Health MonitoringAcpi Features Auto-Switching Voltage Regulator for the CPU CoreSlow Blinking LED for Suspend-State Indicator Thermal Management/CPU VRM OverheatPower Supply Main Switch Override MechanismExternal Modem Ring-On WOR Wake-On-LAN WOLSuper I/O Static-Sensitive Devices PrecautionsUnpacking Processor and Heatsink Installation CPU InstallationHeatsink Installation To Un-install the Heatsink Empty socket Processor installedMounting the Motherboard in the Chassis Dimm Installation See Figure Installing DIMMsMemory Support Control Panel Connectors/IO Ports Back Panel Connectors/IO PortsJF1 Header Pins Front Control PanelPower LED Front Control Panel Pin Definitions NMI ButtonNIC1/NIC2 LED Indicators HDD LEDOverheat/Fan Fail LED Power Fail LEDOH/Fan Fail LED PWR Fail LED Power Button Reset ButtonReset PWR Button Connecting Cables ATX Power ConnectorSecondary Power Connectors Pin PWRChassis Intrusion Universal Serial Bus USBWake-On-LAN Wake-On-RingSerial Ports Glan Giga-bit Ethernet PortsATX PS/2 Keyboard and PS/2 Mouse Ports Fan HeadersPower Supply Failure VGA ConnectorPWR Supply Fail SMB Power I2 C ConnectorSMB Header Power LED/Speaker JD1 Compact Flash Card PWR Connectors JWF1, JWF2Jtag Connector Alarm Reset JAR1Glan Ports Enable/Disable Jumper SettingsExplanation Jumpers Cmos Clear Watch DogVGA Enable/Disable FSB Speed SelectScsi Controller Enable/ Disable *For X6QT8 only Scsi Termination Enable/ Disable *For X6QT8 only3rd PWR Supply PWR Failure Detect JP13 3rd PWR Fail DetectOnboard Indicators Glan LEDsOverheat LED JOH1 LeftRightOnboard Power LED LE1 Scsi Channel Indicators DA1, DA2 *X6QT8 onlyDA1 DA2 LE1 Floppy, IPMI, Hard Disk Drive and Scsi Connections Floppy ConnectorFloppy IDE Connectors IDE Drive Connectors Pin Definitions IDEUltra320 Scsi Connectors InstallationX6QT8 Only Ipmi 2.0 SocketPage Troubleshooting Procedures Before Power OnNo Power Losing the System’s Setup ConfigurationTechnical Support Procedures Memory ErrorsFrequently Asked Questions Returning Merchandise for Service Starting the Setup Utility How To Change the Configuration DataIntroduction Main Setup ProcessorsSystem Memory System Time/System DateConfigure Advanced CPU Settings Advanced SettingsCPU Configuration Sub-Menu Hyper-Threading Technology Max Cpuid Value LimitIntel R C-State Technology IDE Configuration Sub-Menu DMA Mode A.R.T. For Hard disk drivesFloppy Configuration PCI/PnP ConfigurationSuper IO Configuration Submenu Advanced Chipset Settings Apci Configuration Event Log ConfigurationTemperatures CPU Overheat Temperature Hardware Health ConfigurationFan Speed VoltageActive State Power Management MPS ConfigurationPCI Express Configuration MPS RevisionSmbios Configuration Remote Access ConfigurationUSB Configuration Bios Settings Configuration Interrupt 19 CaptureBoot Settings Watch Dog TimerRestore on AC Power Loss Resume On Modem RingBoot Device Priority Hard Disk DrivesRemovable Drives CD/DVD DrivesSecurity Settings Load Optimal Defaults Exit OptionsSaving Changes and Exit Discarding Changes and ExitLoad Fail-Safe Defaults Appendix a Bios Error Beep Codes Beep Code Error Message DescriptionX6QT8/X6QTE+ User’s Manual Uncompressed Initialization Codes D0h D1h D3h D4h D5hBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Combined Mode ATA Operate ModeIntroduction to the Intel ICH5R I/O Controller Hub Adaptec Embedded Serial ATA with HostRAID Controller Driver Using the Adaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACUManaging Arrays Viewing Array Properties From the ARC menu, select Array Configuration Utility ACUEnter Deleting ArraysCreating Arrays To create an arrayAssigning Array Properties Raid Level Create Via When Appropriate When you are fi nished, press Done as the screen shown below Deleting a Bootable Array Adding a Bootable ArrayCtrl+B Initializing Disk Drives To initialize drivesPage Page Rebuilding Arrays To Rebuild an arrayUsing the Disk Utilities To access the disk utilitiesPage You can choose from the following options To Exit Adaptec RAID Configuration UtilityInstalling Intels ICH5R Driver by Adaptec and the Windows OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control