SUPER MICRO Computer X6QT8 Hardware Health Configuration, Temperatures CPU Overheat Temperature

Page 69

Chapter 4: AMI BIOS

￿Hardware Health Configuration

This feature allows the AMI BIOS to automatically display the status of the follow- ing items:

￿Temperatures

CPU Overheat Temperature

This feature allows the user to set the CPU Overheat temperature threshold. The options range from 65oC to 90oC. Use the <+> and <-> keys to set the desired setting. The default setting is 78oC.

The AMI BIOS will automatically monitor and display the following information:

CPU1 Temperature, CPU2 Temperature, CPU3 Temperature, CPU4 Tempera- ture and System Temperature

￿Fan Speed

Fan Speed Control:

This feature allows the user to decide how the system controls the speeds of the onboard fans. The CPU temperature and the fan speed are correlative. When the CPU on-die temperature increases, the fan speed will also increase, and vice versa. Select “Workstation” if your system is used as a workstation. Select “Server” if your system is used as a server. Select “Disable” to disable the fan speed control func- tion to allow the onboard fans to constantly run at full speed (12V). The options are Disable, 3-pin (Server), and 3-pin (Workstation).

Fan1-Fan9 Speeds

￿Voltage

Voltage Monitoring

CPU1-CPU4 Vcore

+3.3V,

+5V,

+12Vcc,

-12Vcc,

+3.3V Standby

4-11

Image 69
Contents Super Page Conventions Used in this Manual About This ManualTable of Contents Table of Contents Troubleshooting BiosAppendices Overview ChecklistHeadquarters Contacting SupermicroEurope Asia-PacificX6QT8 Image Important Notes to the UserSuper X6QT8 Jumper Description Default Setting Quick Reference X6QT8Description LED Indicator Description Super Quick Reference X6QTE+ Memory Motherboard FeaturesChipset Expansion Slots *See Note 3 onLED Indicators Acpi Power FeaturesDimensions SoftwareBlock Diagram of the E8501 Chipset E8501 Chipset Chipset OverviewIndependent Memory Interface InterfacesPC Health Monitoring Special FeaturesAuto-Switching Voltage Regulator for the CPU Core Acpi FeaturesSlow Blinking LED for Suspend-State Indicator Thermal Management/CPU VRM OverheatMain Switch Override Mechanism Power SupplyExternal Modem Ring-On WOR Wake-On-LAN WOLSuper I/O Precautions Static-Sensitive DevicesUnpacking CPU Installation Processor and Heatsink InstallationHeatsink Installation To Un-install the Heatsink Processor installed Empty socketMounting the Motherboard in the Chassis Installing DIMMs Dimm Installation See FigureMemory Support Back Panel Connectors/IO Ports Control Panel Connectors/IO PortsFront Control Panel JF1 Header PinsFront Control Panel Pin Definitions NMI Button Power LEDHDD LED NIC1/NIC2 LED IndicatorsPower Fail LED Overheat/Fan Fail LEDOH/Fan Fail LED PWR Fail LED Reset Button Power ButtonReset PWR Button ATX Power Connector Connecting CablesSecondary Power Connectors Pin PWRUniversal Serial Bus USB Chassis IntrusionWake-On-Ring Wake-On-LANGlan Giga-bit Ethernet Ports Serial PortsFan Headers ATX PS/2 Keyboard and PS/2 Mouse PortsVGA Connector Power Supply FailurePWR Supply Fail Connector SMB Power I2 CSMB Header Compact Flash Card PWR Connectors JWF1, JWF2 Power LED/Speaker JD1Alarm Reset JAR1 Jtag ConnectorJumper Settings Glan Ports Enable/DisableExplanation Jumpers Watch Dog Cmos ClearFSB Speed Select VGA Enable/DisableScsi Termination Enable/ Disable *For X6QT8 only Scsi Controller Enable/ Disable *For X6QT8 only3rd PWR Fail Detect 3rd PWR Supply PWR Failure Detect JP13Glan LEDs Onboard IndicatorsOverheat LED JOH1 LeftRightScsi Channel Indicators DA1, DA2 *X6QT8 only Onboard Power LED LE1DA1 DA2 LE1 Floppy Connector Floppy, IPMI, Hard Disk Drive and Scsi ConnectionsFloppy IDE Drive Connectors Pin Definitions IDE IDE ConnectorsInstallation Ultra320 Scsi ConnectorsX6QT8 Only Ipmi 2.0 SocketPage Before Power On Troubleshooting ProceduresNo Power Losing the System’s Setup ConfigurationMemory Errors Technical Support ProceduresFrequently Asked Questions Returning Merchandise for Service How To Change the Configuration Data Starting the Setup UtilityIntroduction Processors Main SetupSystem Memory System Time/System DateAdvanced Settings Configure Advanced CPU SettingsCPU Configuration Sub-Menu Max Cpuid Value Limit Hyper-Threading TechnologyIntel R C-State Technology IDE Configuration Sub-Menu A.R.T. For Hard disk drives DMA ModePCI/PnP Configuration Floppy ConfigurationSuper IO Configuration Submenu Advanced Chipset Settings Event Log Configuration Apci ConfigurationHardware Health Configuration Temperatures CPU Overheat TemperatureFan Speed VoltageMPS Configuration Active State Power ManagementPCI Express Configuration MPS RevisionRemote Access Configuration Smbios ConfigurationUSB Configuration Interrupt 19 Capture Bios Settings ConfigurationWatch Dog Timer Boot SettingsRestore on AC Power Loss Resume On Modem RingHard Disk Drives Boot Device PriorityRemovable Drives CD/DVD DrivesSecurity Settings Exit Options Load Optimal DefaultsSaving Changes and Exit Discarding Changes and ExitLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesX6QT8/X6QTE+ User’s Manual D0h D1h D3h D4h D5h Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page ATA Operate Mode Combined ModeIntroduction to the Intel ICH5R I/O Controller Hub Adaptec Embedded Serial ATA with HostRAID Controller Driver Using the Array Configuration Utility ACU Using the Adaptec RAID Configuration Utility ARCManaging Arrays From the ARC menu, select Array Configuration Utility ACU Viewing Array PropertiesEnter Deleting ArraysTo create an array Creating ArraysAssigning Array Properties Raid Level Create Via When Appropriate When you are fi nished, press Done as the screen shown below Adding a Bootable Array Deleting a Bootable ArrayCtrl+B To initialize drives Initializing Disk DrivesPage Page To Rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesPage To Exit Adaptec RAID Configuration Utility You can choose from the following optionsInstalling Intels ICH5R Driver by Adaptec and the Windows OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control