SUPER MICRO Computer 5014C-MF user manual IDE Connector, IDE Drive Connectors Pin Deﬁnitions IDE

Page 61

Chapter 5: Advanced Motherboard Setup

IDE Connector

There are no jumpers to conﬁ gure the onboard IDE interface "IDE". See the table below for pin deﬁ ni- tions.

IDE Drive Connectors

Pin Deﬁnitions (IDE)

Pin# Deﬁ nition

1Reset IDE

3Host Data 7

5 Host Data 6

7 Host Data 5

9 Host Data 4

11 Host Data 3

13 Host Data 2

15Host Data 1

17Host Data 0

19Ground

21DRQ3

23I/O Write

25I/O Read

27IOCHRDY

29DACK3

31IRQ14

33Addr1

35Addr0

37Chip Select 0

39 Activity

Pin # Deﬁ nition

2Ground

4Host Data 8

6 Host Data 9

8 Host Data 10

10 Host Data 11

12 Host Data 12

14 Host Data 13

16Host Data 14

18Host Data 15

20Key

22Ground

24Ground

26Ground

28BALE

30Ground

32IOCS16

34Ground

36Addr2

38Chip Select 1

40 Ground

5-23

Image 61

Contents Super Page About This Manual PrefaceManual Organization Advanced Motherboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents Advanced Motherboard Setup System SafetyBios Advanced Chassis SetupAppendices Page Overview Chapter IntroductionProcessor Memory Motherboard FeaturesSerial ATA PCI Expansion SlotsOnboard Controllers/Front Side Ports Other FeaturesIntel E7221 Chipset System Block Diagram System Power Server Chassis FeaturesSerial ATA Subsystem Control PanelFront I/O Panel Cooling SystemHeadquarters Contacting SupermicroEurope Asia-PaciﬁcPage Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Basic Installation Procedure Installing the System into a RackInstalling with Optional Rackmount Kit CSE-PT8 Installing Chassis Rails Installing the Chassis RailsInstalling the Server into the Rack Installing the Rack RailsInstalling the Server into a Rack Installing the Server into a Telco RackInstalling the Server into a Telco Rack Accessing the inside of the system Figure Checking the Motherboard SetupAccessing the Inside of the System Accessing the drive bays Checking the Drive Bay SetupPage Control Panel Buttons Chapter System InterfaceControl Panel LEDs Page Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Motherboard SetupHandling the Motherboard Unpacking Motherboard InstallationConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control PanelI/O Ports Control Panel Header PinsInstalling the Processor Installed Heatsink Removal Heatsink InstallationMemory support Installing MemoryBit PCI-X slot Adding PCI CardsP8SCT Super Motherboard DetailsConnector Description Jumper Description Default SettingP8SCT Quick Reference Power Supply Connectors Connector DeﬁnitionsPwon Connector Reset ConnectorNIC2 JLAN2 LED Overheat LED OHNMI Button Power On LEDFan Headers ATX PS/2 Keyboard and PS/2 Mouse PortsUniversal Serial Bus USB Chassis IntrusionWake-On-LAN JLAN1/2 Ethernet PortsWake-On-Ring Power LEDSerial Ports Speaker Connector Jumper SettingsExplanation Jumpers Cmos ClearUSB Wake-Up System Power Force OnKeyboard Wake-Up JLAN1/JLAN2 Enable Disable Watch Dog Enable/DisableSMBus to PCI PCI-X Slot Speed Select Onboard IndicatorsCPU Front Side Bus Speed JLAN1/JLAN2 LEDsParallel Port, Floppy and IDE Drive Connections Parallel Port ConnectorFloppy Drive Connector Pin Deﬁnitions Floppy Floppy ConnectorIDE Drive Connectors Pin Deﬁnitions IDE IDE ConnectorPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Chassis Front View Control PanelAccessing the Drive Bay Drive Bay Installation/RemovalSystem Fan System Fan FailureInstalling/removing a Serial ATA drive Serial ATA Drive InstallationInternal Hard Drive Bay Power Supply Failure Power SupplyReplacing the Power Supply How To Change the Conﬁguration Data System BiosStarting the Setup Utility ChapterMain Bios Setup Running SetupLegacy Diskette A/Legacy Diskette B Date/TimeSwap Floppy Drive IDE HDD Auto-Detection Access ModeIDE Channel 0 to IDE Channel 3 Master Halt OnAdvanced Bios Features Advanced Bios SetupQuick Boot Quiet BootAdvanced Chipset Control On-Chip Serial ATA Pata IDE ModeSata Port USB ControllerEPP Mode Select Parallel Port ModeECP Mode Use DMA Power On FunctionOnboard LAN Boot ROM Reset Conﬁguration Data4PnP/PCI Conﬁguration Initial Display FromMaximum Payload Size PCI-E Compliance ModePCI-X Frequency Hardware Monitors CPU Warning TemperatureProcessor & Clock Options DMI Event Log Console Redirection Console RedirectionBaud Rate Agent Connect ViaSet User Password Set Supervisor PasswordPassword Check SecurityFirst Boot Device BootSecond Boot Device Third Boot DeviceExit Page Appendix a Bios Post Messages Page Appendix B Bios Post Codes Page Appendix B Bios Post Codes Page Appendix B Bios Post Codes Page Serial ATA Sata Conﬁguring Intels ICH6R Sata RAID FunctionIntels ICH6R Serial RAID ATA Operating ModesSata Operating Modes Conﬁguring Bios Settings Native ModeAccessing the LSI Sata RAID Utility Using the LSI ICH6R Sata RAID Utility DriverCreating New a Sata RAID Page Page Page Initializing Disk Drives Creating Hot Spare Drives Page Installing WindowsXP/2000/2003 for RAID Systems Installing Other Drivers Installing Other Software Programs and DriversSupero Doctor Supero Doctor III Remote Control Appendix D System Speciﬁcations Power Supply WeightSystem Cooling System Input Requirements