SUPER MICRO Computer 5014C-MF On-Chip Serial ATA, Pata IDE Mode, Sata Port, USB Controller

Page 75

Chapter 7: BIOS

On-Chip Serial ATA

Select "Disabled" to disable the SATA Controller. Select "Auto" to allow the BIOS to conﬁ gure the SATA Controller automatically. Select "Combined Mode" to use PATA and SATA Combined Mode. The maximum of 2 IDE drives in each channel is allowed. Select "Enhanced Mode" to enable both SATA and PATA. This mode will support up to 6 IDE drives. Select "SATA Only" to allow SATA to operate in "Legacy Mode".

PATA IDE Mode

When the item -On-chip Serial ATA is set to Combined Mode, the user can select either Primary or Secondary for Parallel ATA IDE. The options are Primary and Secondary. If On-chip Serial ATA is set to Enhanced Mode, only Serial ATA will be activated, and Primary PATA IDE will be available. Secondary PATA IDE will not be available.

SATA Port

This setting allows you conﬁ gure the setting for the SATA port. The options are P1 and P3 is Secondary.

USB Controller

This setting allows you to enable or disable the USB Controller. The options are Enabled and Disabled.

USB 2.0 Controller

This setting allows you to enable or disable USB 2.0 (EHCI) Controller. The options are Enabled and Disabled.

USB Legacy Support

This setting allows you to enable or disable the functions of USB, Keyboard/Mouse under POST and DOS. The options are "Disabled" and "Enabled."

7-7

Image 75

Contents Super Page Preface About This ManualManual Organization Bios System SafetyAdvanced Motherboard Setup Advanced Chassis SetupPreface Table of Contents Advanced Motherboard Setup System SafetyBios Advanced Chassis SetupAppendices Page Overview Chapter IntroductionPCI Expansion Slots Motherboard FeaturesProcessor Memory Serial ATAOnboard Controllers/Front Side Ports Other FeaturesIntel E7221 Chipset System Block Diagram Control Panel Server Chassis FeaturesSystem Power Serial ATA SubsystemFront I/O Panel Cooling SystemAsia-Paciﬁc Contacting SupermicroHeadquarters EuropePage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Installing the System into a Rack Basic Installation ProcedureInstalling with Optional Rackmount Kit CSE-PT8 Installing Chassis Rails Installing the Chassis RailsInstalling the Server into the Rack Installing the Rack RailsInstalling the Server into a Rack Installing the Server into a Telco RackInstalling the Server into a Telco Rack Accessing the inside of the system Figure Checking the Motherboard SetupAccessing the Inside of the System Accessing the drive bays Checking the Drive Bay SetupPage Control Panel Buttons Chapter System InterfaceControl Panel LEDs Page Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsChapter Advanced Motherboard Setup PrecautionsHandling the Motherboard Unpacking Motherboard InstallationConnecting the Control Panel Connecting CablesConnecting Data Cables Connecting Power CablesI/O Ports Control Panel Header PinsInstalling the Processor Installed Heatsink Removal Heatsink InstallationMemory support Installing MemoryBit PCI-X slot Adding PCI CardsP8SCT Super Motherboard DetailsJumper Description Default Setting Connector DescriptionP8SCT Quick Reference Reset Connector Connector DeﬁnitionsPower Supply Connectors Pwon ConnectorNIC2 JLAN2 LED Overheat LED OHATX PS/2 Keyboard and PS/2 Mouse Ports Power On LEDNMI Button Fan HeadersJLAN1/2 Ethernet Ports Chassis IntrusionUniversal Serial Bus USB Wake-On-LANPower LED Wake-On-RingSerial Ports Cmos Clear Jumper SettingsSpeaker Connector Explanation JumpersSystem Power Force On USB Wake-UpKeyboard Wake-Up Watch Dog Enable/Disable JLAN1/JLAN2 Enable DisableSMBus to PCI JLAN1/JLAN2 LEDs Onboard IndicatorsPCI-X Slot Speed Select CPU Front Side Bus SpeedParallel Port, Floppy and IDE Drive Connections Parallel Port ConnectorFloppy Drive Connector Pin Deﬁnitions Floppy Floppy ConnectorIDE Drive Connectors Pin Deﬁnitions IDE IDE ConnectorPage Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Chassis Front View Control PanelSystem Fan Failure Drive Bay Installation/RemovalAccessing the Drive Bay System FanInstalling/removing a Serial ATA drive Serial ATA Drive InstallationInternal Hard Drive Bay Power Supply Power Supply FailureReplacing the Power Supply Chapter System BiosHow To Change the Conﬁguration Data Starting the Setup UtilityMain Bios Setup Running SetupDate/Time Legacy Diskette A/Legacy Diskette BSwap Floppy Drive Halt On Access ModeIDE HDD Auto-Detection IDE Channel 0 to IDE Channel 3 MasterQuiet Boot Advanced Bios SetupAdvanced Bios Features Quick BootAdvanced Chipset Control USB Controller Pata IDE ModeOn-Chip Serial ATA Sata PortPower On Function Parallel Port ModeEPP Mode Select ECP Mode Use DMAInitial Display From Reset Conﬁguration DataOnboard LAN Boot ROM 4PnP/PCI ConﬁgurationPCI-E Compliance Mode Maximum Payload SizePCI-X Frequency Hardware Monitors CPU Warning TemperatureProcessor & Clock Options DMI Event Log Agent Connect Via Console RedirectionConsole Redirection Baud RateSecurity Set Supervisor PasswordSet User Password Password CheckThird Boot Device BootFirst Boot Device Second Boot DeviceExit Page Appendix a Bios Post Messages Page Appendix B Bios Post Codes Page Appendix B Bios Post Codes Page Appendix B Bios Post Codes Page ATA Operating Modes Conﬁguring Intels ICH6R Sata RAID FunctionSerial ATA Sata Intels ICH6R Serial RAIDSata Operating Modes Conﬁguring Bios Settings Native ModeAccessing the LSI Sata RAID Utility Using the LSI ICH6R Sata RAID Utility DriverCreating New a Sata RAID Page Page Page Initializing Disk Drives Creating Hot Spare Drives Page Installing WindowsXP/2000/2003 for RAID Systems Installing Other Drivers Installing Other Software Programs and DriversSupero Doctor Supero Doctor III Remote Control Appendix D System Speciﬁcations System Input Requirements WeightPower Supply System Cooling