SUPER MICRO Computer 5014C-MF user manual Installing Memory, Memory support

Page 46

SUPERSERVER 5014C-MF User's Manual

5-6 Installing Memory

!

CAUTION! Exercise extreme care when installing or removing DIMM modules to prevent any possible damage.

1. Memory support

The P8SCT supports up to 4 GB of dual or single-channel, unbuffered ECC or unbuffered non-ECC DDR2-533 or DDR2-400 SDRAM. Both interleaved and non- interleaved memory are supported, so you may populate any number of DIMM slots. Populating two slots at a time (starting with Bank 1: DIMM1A and DIMM 1B) with the same size and type of memory modules will result in dual-channel(two-way interleaved) operation, which is faster than single channel operation.

2. Installing memory modules

Insert each memory module vertically. Pay attention to the notches along the bottom of the module to prevent inserting it incorrectly. Gently press down on the DIMM module until it snaps into place in the slot (see Figure 5-3).

Figure 5-3. DIMM Installation

Notch

Release

TabNote: Notches should align

with their receptive points on the slot

Notch

Release

Tab

To Install: Insert module vertically and press down until it snaps into place. Pay attention to the bottom

notches.

To Remove: Use your thumbs to gently push each release tab outward to free the DIMM from the

slot.

5-8

Image 46
Contents Super Page About This Manual PrefaceManual Organization Advanced Chassis Setup System SafetyAdvanced Motherboard Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosAppendices Page Chapter Introduction OverviewSerial ATA Motherboard FeaturesProcessor Memory PCI Expansion SlotsOther Features Onboard Controllers/Front Side PortsIntel E7221 Chipset System Block Diagram Serial ATA Subsystem Server Chassis FeaturesSystem Power Control PanelCooling System Front I/O PanelEurope Contacting SupermicroHeadquarters Asia-PacificPage Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Basic Installation Procedure Installing the System into a RackInstalling with Optional Rackmount Kit CSE-PT8 Installing the Chassis Rails Installing Chassis RailsInstalling the Rack Rails Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a RackInstalling the Server into a Telco Rack Checking the Motherboard Setup Accessing the inside of the system FigureAccessing the Inside of the System Checking the Drive Bay Setup Accessing the drive baysPage Chapter System Interface Control Panel ButtonsControl Panel LEDs Page Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryPrecautions Chapter Advanced Motherboard SetupHandling the Motherboard Motherboard Installation UnpackingConnecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelControl Panel Header Pins I/O PortsInstalling the Processor Installed Heatsink Installation Heatsink RemovalInstalling Memory Memory supportAdding PCI Cards Bit PCI-X slotMotherboard Details P8SCT SuperConnector Description Jumper Description Default SettingP8SCT Quick Reference Pwon Connector Connector DefinitionsPower Supply Connectors Reset ConnectorOverheat LED OH NIC2 JLAN2 LEDFan Headers Power On LEDNMI Button ATX PS/2 Keyboard and PS/2 Mouse PortsWake-On-LAN Chassis IntrusionUniversal Serial Bus USB JLAN1/2 Ethernet PortsWake-On-Ring Power LEDSerial Ports Explanation Jumpers Jumper SettingsSpeaker Connector Cmos ClearUSB Wake-Up System Power Force OnKeyboard Wake-Up JLAN1/JLAN2 Enable Disable Watch Dog Enable/DisableSMBus to PCI CPU Front Side Bus Speed Onboard IndicatorsPCI-X Slot Speed Select JLAN1/JLAN2 LEDsParallel Port Connector Parallel Port, Floppy and IDE Drive ConnectionsFloppy Connector Floppy Drive Connector Pin Definitions FloppyIDE Connector IDE Drive Connectors Pin Definitions IDEPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front ViewSystem Fan Drive Bay Installation/RemovalAccessing the Drive Bay System Fan FailureSerial ATA Drive Installation Installing/removing a Serial ATA driveInternal Hard Drive Bay Power Supply Failure Power SupplyReplacing the Power Supply Starting the Setup Utility System BiosHow To Change the Configuration Data ChapterRunning Setup Main Bios SetupLegacy Diskette A/Legacy Diskette B Date/TimeSwap Floppy Drive IDE Channel 0 to IDE Channel 3 Master Access ModeIDE HDD Auto-Detection Halt OnQuick Boot Advanced Bios SetupAdvanced Bios Features Quiet BootAdvanced Chipset Control Sata Port Pata IDE ModeOn-Chip Serial ATA USB ControllerECP Mode Use DMA Parallel Port ModeEPP Mode Select Power On Function4PnP/PCI Configuration Reset Configuration DataOnboard LAN Boot ROM Initial Display FromMaximum Payload Size PCI-E Compliance ModePCI-X Frequency CPU Warning Temperature Hardware MonitorsProcessor & Clock Options DMI Event Log Baud Rate Console RedirectionConsole Redirection Agent Connect ViaPassword Check Set Supervisor PasswordSet User Password SecuritySecond Boot Device BootFirst Boot Device Third Boot DeviceExit Page Appendix a Bios Post Messages Page Appendix B Bios Post Codes Page Appendix B Bios Post Codes Page Appendix B Bios Post Codes Page Intels ICH6R Serial RAID Configuring Intels ICH6R Sata RAID FunctionSerial ATA Sata ATA Operating ModesConfiguring Bios Settings Native Mode Sata Operating ModesUsing the LSI ICH6R Sata RAID Utility Driver Accessing the LSI Sata RAID UtilityCreating New a Sata RAID Page Page Page Initializing Disk Drives Creating Hot Spare Drives Page Installing WindowsXP/2000/2003 for RAID Systems Installing Other Software Programs and Drivers Installing Other DriversSupero Doctor Supero Doctor III Remote Control Appendix D System Specifications System Cooling WeightPower Supply System Input Requirements