Seagate ST336807FC manual Active LED Out conditions, Enable port bypass signals

Page 76

9.5.8Active LED Out

The Active LED Out signal is driven by the drive as indicated in Table 29.

Table 29: Active LED Out conditions

Normal command activity	LED status

Spun down and no activity	Slow blink (20% on and 80% off a 2 sec cycle)

Spun down and activity (command executing)	On

Spun up and no activity	On

Spun up and activity (command executing)	Off

Spinning up or down	Blinks steadily (50% on and 50% off)

Format in progress, each cylinder change	Toggles on/off

The Active LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +5 volt supply through an appropriate current limiting resistor. The LED and the current limiting resistor are external to the drive.

9.5.9Enable port bypass signals

The – Enable Bypass Port A (– EN BYP Port A) and – Enable Bypass Port B (– EN BYP Port B) signals control the port bypass circuits (PBC) located external to the disc drive. The PBC allows a loop to remain functional in the event of a drive failure or removal. When these signals are active, low, the PBC bypasses the drive on the associated port. When an Enable Bypass signal is active, the corresponding Port Bypass LED signal in con- nector J1 is driven low by the disc drive. A pull down resistor, 1K, located with the PBC should be used to insure the bypass is enabled if the disc drive is not installed.

The Enable Bypass signal is active under failing conditions within the drive, on detection of the Loop Port Bypass primitive sequence, or on removal of the drive. In the bypass state the drive continues to receive on the inbound fibre. Enable Bypass may be deactivated by detection of a Loop Port Enable primitive sequence if the drive has completed self-test and a hardware failure is not present.

Failure modes detected by the disc drive that will enable bypass include:

•Transmitter/receiver wrap test failure

•Loss of receive clock

•Loss of transmission clock

•Drive interface hardware error

64	Cheetah 10K.7 36GB FC Product Manual, Rev. A

Image 76

Contents Cheetah 10K.7 FC Page Cheetah 10K.7 FC Page Rev. a 05/04/05 All. Initial release Revision status summary sheetRevision Date Sheets Affected Page Contents Physical/electrical specifications Defect and error managementInstallation Interface requirementsSeagate Technology support services Viii Cheetah 10K.7 36GB FC Product Manual, Rev. a List of Figures Cheetah 10K.7 FC family disc driveCheetah 10K.7 36GB FC Product Manual, Rev. a Scope Cheetah 10K.7 FC family disc driveCheetah 10K.7 36GB FC Product Manual, Rev. a Applicable standards and reference documentation StandardsElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance European Union Restriction of Hazardous Substances RoHSReference documents Fibre Channel Interface ManualCheetah 10K.7 36GB FC Product Manual, Rev. a General description Standard features Media descriptionPerformance ReliabilityFormatted capacities Programmable drive capacityFactory-installed options Factory-installed accessoriesUser-installed accessories Internal drive characteristics Performance characteristicsST336807FC Seek performance characteristics Access timeFormat command execution time in minutes Generalized performance characteristicsPrefetch/multi-segmented cache control Start/stop timeCache operation Caching write data Prefetch operation Cheetah 10K.7 36GB FC Product Manual, Rev. a Error rates Reliability specificationsRecoverable Errors Reliability and service 4 S.M.A.R.T Hot plugging the driveControlling S.M.A.R.T Performance impact MillisecondsReporting control Determining rateParameter Code Description Temperature Log page 0DhDrive Self Test DST State of the drive prior to testing DST Failure DefinitionImplementation Invoking DSTProduct warranty Short test Function Code 001bExtended test Function Code 010b Log page entriesShipping Product repair and return informationPhysical/electrical specifications AC power requirementsDC power requirements ST336807FC DC power requirementsPower sequencing General DC power requirement notesConducted noise immunity Typical ST336807FC drive, 2 Gbit, +12V current profile Typical ST336807FC drive, 2 Gbit, +5V current profilePower dissipation ST336807FCTemperature Environmental limitsRelative humidity Effective altitude sea levelShock and vibration Package size Packaged/product weight Drop heightShock Recommended mounting Vibration Air cleanlinessCorrosive environment Mechanical specifications AcousticsMounting configuration dimensions Drive internal defects/errors Defect and error managementDrive error recovery procedures 77.7 Background Media Scan FC-AL system errorsMedia Pre-Scan Cheetah 10K.7 36GB FC Product Manual, Rev. a Installation Drive ID/option selectionLED connections Physical interface Drive FrontDrive orientation 1 J6 connector requirementsCooling Drive mounting GroundingFC-AL features Fibre Channel link service framesLink services supported Type of frame Link serviceFibre Channel task management functions Fibre Channel Scsi FCP task management functionsFibre Channel task management responses FC Scsi FCP response codesNPort login Plogi payload Fibre Channel port loginBytes Fibre Channel port login accept NPort Login Accept ACC payloadFibre Channel Process Login Process Login Plri payloadFibre Channel Process Login Accept Process Login Accept ACC payloadFibre Channel fabric login Fabric Login Flogi payloadFibre Channel fabric accept login Fabric Login Accept ACC payloadDual port support Fibre Channel Arbitrated Loop optionsFC-AL options supported Option SupportedSupported commands Scsi commands supportedCommand code Supported Command name Supported commands Supported commands Supported commands Supported commands Mode Sense data Inquiry dataCheetah 10K.7 FC inquiry data Bytes Data hexPage DEF CHG Miscellaneous operating features and conditions Miscellaneous featuresSupported Feature or condition Miscellaneous statusFC-AL physical interface Physical characteristicsPhysical description Connector requirements Part description Positions Part number FeaturesJ6 connector dimensions Electrical descriptionPin descriptions Pin Signal name Signal typeFC-SCA pin descriptions Fault LED Out PowerFC-AL transmitters and receivers Enable port bypass signals Normal command activity LED statusActive LED Out Active LED Out conditionsMotor start control signals Parallel Enclosure Services Interface ESIMotor start controls 11 SEL6 through SEL0 ID linesArbitrated loop physical address Alpa values SettingHex Dec Signal characteristics LED driver signals LED drive signalDifferential Pecl output characteristics Differential Pecl input characteristicsEye diagram data values Link rate GHzCheetah 10K.7 36GB FC Product Manual, Rev. a Seagate Technology support services Internet MySeagate Reseller.seagate.comPresales Support Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call center Presales and Technical Support Warranty Service FAX services-All Europe toll callToll-free support numbers Asia/Pacific support services Publication feedback survey Cheetah 10K.7 36GB FC Product Manual, Rev. a Index NumericsFAN Flogi PBC Page See also cooling