Seagate ST336807FC DST Failure Definition, Implementation, State of the drive prior to testing

Page 34

5.2.6.1DST Failure Definition

The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log page if a functional failure is encountered during DST. The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number of retries required to recover the data.

The following conditions are considered DST failure conditions:

•Seek error after retries are exhausted

•Track-follow error after retries are exhausted

•Read error after retries are exhausted

•Write error after retries are exhausted

Recovered errors will not be reported as diagnostic failures.

5.2.6.2Implementation

This section provides all of the information necessary to implement the DST function on this drive.

5.2.6.2.1State of the drive prior to testing

The drive must be in a ready state before issuing the Send Diagnostic command. There are multiple reasons why a drive may not be ready, some of which are valid conditions, and not errors. For example, a drive may be in process of doing a format, or another DST. It is the responsibility of the host application to determine the “not ready” cause.

While not technically part of DST, a Not Ready condition also qualifies the drive to be returned to Seagate as a failed drive.

A Drive Not Ready condition is reported by the drive under the following conditions:

•Motor will not spin

•Motor will not lock to speed

•Servo will not lock on track

•Drive cannot read configuration tables from the disc

In these conditions, the drive responds to a Test Unit Ready command with an 02/04/00 or 02/04/03 code.

5.2.6.2.2Invoking DST

To invoke DST, submit the Send Diagnostic command with the appropriate Function Code (001b for the short test or 010b for the extended test) in bytes 1, bits 5, 6, and 7. Refer to the Fibre Channel Interface Product Manual, part number 77767496, for additional information about invoking DST.

5.2.6.2.3Short and extended tests

DST has two testing options:

1.short

2.extended

These testing options are described in the following two subsections.

Each test consists of three segments: an electrical test segment, a servo test segment, and a read/verify scan segment.

22

Cheetah 10K.7 36GB FC Product Manual, Rev. A

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Cheetah 10K.7 FC Page Cheetah 10K.7 FC Page Rev. a 05/04/05 All. Initial release Revision status summary sheetRevision Date Sheets Affected Page Contents Installation Physical/electrical specificationsDefect and error management Interface requirementsSeagate Technology support services Viii Cheetah 10K.7 36GB FC Product Manual, Rev. a List of Figures Cheetah 10K.7 FC family disc driveCheetah 10K.7 36GB FC Product Manual, Rev. a Scope Cheetah 10K.7 FC family disc driveCheetah 10K.7 36GB FC Product Manual, Rev. a Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityElectromagnetic compliance European Union Restriction of Hazardous Substances RoHSReference documents Fibre Channel Interface ManualCheetah 10K.7 36GB FC Product Manual, Rev. a General description Standard features Media descriptionFormatted capacities PerformanceReliability Programmable drive capacityFactory-installed options Factory-installed accessoriesUser-installed accessories Internal drive characteristics Performance characteristicsST336807FC Format command execution time in minutes Seek performance characteristicsAccess time Generalized performance characteristicsPrefetch/multi-segmented cache control Start/stop timeCache operation Caching write data Prefetch operation Cheetah 10K.7 36GB FC Product Manual, Rev. a Error rates Reliability specificationsRecoverable Errors Reliability and service 4 S.M.A.R.T Hot plugging the driveControlling S.M.A.R.T Reporting control Performance impactMilliseconds Determining rateParameter Code Description Temperature Log page 0DhDrive Self Test DST Implementation State of the drive prior to testingDST Failure Definition Invoking DSTExtended test Function Code 010b Product warrantyShort test Function Code 001b Log page entriesShipping Product repair and return informationDC power requirements Physical/electrical specificationsAC power requirements ST336807FC DC power requirementsPower sequencing General DC power requirement notesConducted noise immunity Typical ST336807FC drive, 2 Gbit, +12V current profile Typical ST336807FC drive, 2 Gbit, +5V current profilePower dissipation ST336807FCRelative humidity TemperatureEnvironmental limits Effective altitude sea levelShock and vibration Package size Packaged/product weight Drop heightShock Recommended mounting Vibration Air cleanlinessCorrosive environment Mechanical specifications AcousticsMounting configuration dimensions Drive internal defects/errors Defect and error managementDrive error recovery procedures 77.7 Background Media Scan FC-AL system errorsMedia Pre-Scan Cheetah 10K.7 36GB FC Product Manual, Rev. a Installation Drive ID/option selectionLED connections Physical interface Drive FrontDrive orientation 1 J6 connector requirementsCooling Drive mounting GroundingLink services supported FC-AL featuresFibre Channel link service frames Type of frame Link serviceFibre Channel task management responses Fibre Channel task management functionsFibre Channel Scsi FCP task management functions FC Scsi FCP response codesNPort login Plogi payload Fibre Channel port loginBytes Fibre Channel Process Login Fibre Channel port login acceptNPort Login Accept ACC payload Process Login Plri payloadFibre Channel fabric login Fibre Channel Process Login AcceptProcess Login Accept ACC payload Fabric Login Flogi payloadFibre Channel fabric accept login Fabric Login Accept ACC payloadFC-AL options supported Dual port supportFibre Channel Arbitrated Loop options Option SupportedSupported commands Scsi commands supportedCommand code Supported Command name Supported commands Supported commands Supported commands Supported commands Cheetah 10K.7 FC inquiry data Mode Sense dataInquiry data Bytes Data hexPage DEF CHG Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusFC-AL physical interface Physical characteristicsPhysical description Connector requirements Part description Positions Part number FeaturesJ6 connector dimensions Electrical descriptionPin descriptions Pin Signal name Signal typeFC-SCA pin descriptions Fault LED Out PowerFC-AL transmitters and receivers Active LED Out Enable port bypass signalsNormal command activity LED status Active LED Out conditionsMotor start controls Motor start control signalsParallel Enclosure Services Interface ESI 11 SEL6 through SEL0 ID linesArbitrated loop physical address Alpa values SettingHex Dec Signal characteristics Differential Pecl output characteristics LED driver signalsLED drive signal Differential Pecl input characteristicsEye diagram data values Link rate GHzCheetah 10K.7 36GB FC Product Manual, Rev. a Presales Support Seagate Technology support servicesInternet MySeagate Reseller.seagate.com Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call center Presales and Technical Support Warranty Service FAX services-All Europe toll callToll-free support numbers Asia/Pacific support services Publication feedback survey Cheetah 10K.7 36GB FC Product Manual, Rev. a Index NumericsFAN Flogi PBC Page See also cooling
Top Page Image Contents