Seagate ST3450802SS Transmitter signal characteristics, Signal characteristica Units 5Gb/s 0Gb/s

Page 60

9.5.2.2Transmitter signal characteristics

Table 25 specifies the signal requirements at the transmitter end of a TxRx connection as measured into the zero-length test load. All specifications are based on differential measurements.

The OOB sequence is performed at signal voltage levels corresponding to the lowest supported transfer rate. Table 25 specifies the signal characteristics.

Table 25: Transmitter signal characteristics

Signal characteristica

Units

1.5Gb/s

3.0Gb/s

Skewb

ps

20

15

Tx Off Voltagec

mV(P-P)

< 50

< 50

Maximum rise/fall timed

ps

273

137

Minimum rise/fall timed

ps

67

67

Maximum transmitter output imbalancee

%

10

10

OOB offset deltaf

mV

± 25

± 25

OOB common mode deltag

mV

± 50

± 50

aAll tests in this table shall be performed with zero-length test load shown in figure 18.

bThe skew measurement shall be made at the midpoint of the transition with a repeating 0101b pattern on the physical link. The same stable trigger, coherent to the data stream, shall be used for both the Tx+ and Tx- signals. Skew is defined as the time difference between the means of the midpoint crossing times of the Tx+ signal and the Tx- signal.

cThe transmitter off voltage is the maximum A.C. voltage measured at compliance points when the transmitter is unpowered or transmitting D.C. idle (e.g., during idle time of an OOB signal).

dRise/fall times are measured from 20 % to 80 % of the transition with a repeating 0101b pattern on the physical link.

eThe maximum difference between the V+ and V- A.C. RMS transmitter amplitudes measured on a CJTPAT test pattern (see 9.5.2.3.3) into the test load shown in figure 18, as a percentage of the average of the V+ and V- A.C. RMS amplitudes.

fThe maximum difference in the average differential voltage (D.C. offset) component between the burst times and the idle times of an OOB signal.

gThe maximum difference in the average of the common mode voltage between the burst times and the idle times of an OOB signal.

56

Cheetah NS 10K.2 SAS Product Manual, Rev. C

Image 60
Contents Cheetah NS 10K.2 SAS ST3600002SS ST3450802SSPage Contents Defect and error management InstallationSeagate Technology support services Interface requirementsScope Standards, compliance and reference documents StandardsElectromagnetic compatibility Electromagnetic susceptibilityCompliance Reference documents General description Standard features Media descriptionPerformance ReliabilityFactory-installed options Formatted capacitiesProgrammable drive capacity Performance characteristics Internal drive characteristicsAccess time Seek performanceFormat command execution time minutes General performance characteristicsStart/stop time Prefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Reliability specifications Error ratesRecoverable Errors Unrecoverable ErrorsReliability and service Interface errorsPreventive maintenance Hot plugging the drive4 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting controlTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor Drive Self Test DSTDST failure definition ImplementationProduct warranty Short test Function Code 001bExtended test Function Code 010b Shipping Physical/electrical specifications AC power requirementsDC power requirements ST3600002SS DC power requirementsST3450802SS DC power requirements General DC power requirement notesPower sequencing Conducted noise immunityCurrent profiles Typical ST3600002SS drive +5V and +12V current profiles Power dissipation ST3600002SSST3450802SS Temperature a. Operating Environmental limitsRelative humidity Effective altitude sea level a. OperatingShock and vibration ShockPackage size Packaged/product weight Drop height Recommended mountingAir cleanliness Vibration a. Operating-normalAcoustics Corrosive environmentChina Restriction of Hazardous Substances RoHS Directive Mechanical specifications Physical dimensionsDefect and error management Drive internal defects/errorsDrive error recovery procedures 77.81 SAS system errors Background Media ScanMedia Pre-Scan Deferred Auto-ReallocationIdle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Commands supported by Cheetah NS 10K.2 SAS family drivesCommands supported by Cheetah NS 10K.2 SAS family drives Commands supported by Cheetah NS 10K.2 SAS family drives Commands supported by Cheetah NS 10K.2 SAS family drives Inquiry data 2Mode Sense dataBytes Data hex Page 2.1 ST3600002SS Mode Sense data Mode Pages2.2 ST3450802SS Mode Sense data Miscellaneous operating features and conditions Miscellaneous featuresSupported Feature or condition Miscellaneous statusSAS physical interface Datum B Physical characteristics Connector requirementsPin Signal name Signal type Electrical descriptionPin descriptions SAS pin descriptionsSignal characteristics PowerSAS transmitters and receivers Ready LED OutLED drive signal Differential signalsGeneral interface characteristics Eye masks Eye masks overviewReceive eye mask X2OP 0, 5xadditional sinusoidal jitter X1OP Transmitter signal characteristics Signal characteristica Units 5Gb/s 0Gb/sReceiver signal characteristics Signal characteristic Units 5Gb/s 0Gb/sMaximum allowable jitter 5Gb/s m, n 0Gb/s m, n Deterministic jitterqReceiver jitter tolerance Impedance requirements Sheet 15Gb/sa 0Gb/sa Sinusoidal Deterministic Total JitterhImpedance requirements Sheet 2 Electrical TxRx connections= -5, 437dB Shows the zero-length test load SAS-2 Specification compliance Receiver characteristicsAdditional information Seagate Technology support services Presales SupportTechnical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index Page SAS See also cooling Page Seagate Technology LLC
Related manuals
Manual 74 pages 59.57 Kb