Teledyne 460H Table Of Contents, I. 0 INTRODUCTION, Installation, Startup, Operation, Maintenance

Page 3

TABLE OF CONTENTS
SAFETY MESSAGES		II
TABLE OF CONTENTS		III
FIGURES		V
TABLES		VI
I. 0 INTRODUCTION		7
1. 1 PREFACE		7
1.2 WARRANTY POLICY		8
1.3 PRINCIPLE OF OPERATION		9
1.4 SPECIFICATIONS		10
2.0 INSTALLATION		11
2.1 MECHANICAL INSTALLATION		11
2.2 PNEUMATIC CONNECTIONS		12
2.3 AC POWER CONNECTION		13
2.4	ELECTRICAL I/O CONNECTIONS	14
2.4.1	Analog Output	14
2.4.2	Digital Status Outputs	15
2.4.3	Control Inputs	16
2.4.4	RS232/RS485 Serial Communications Port	17
3.0 STARTUP		18
4.0 OPERATION		19
4.1 FRONT PANEL DISPLAY		19
4.1.1 O3 readout		19
4.1.2 Pressure Display		19
4.1.3 Zero Calibration		19
4.1.4 Status LED’s		19
4.2 AUTO-ZEROOPERATION (OPTIONAL)		20
4.2.1 Auto-Zero Installation		20
4.2.2 Auto-Zero Function		20
4.2.3 Auto Zero Error		20
5.0 SERIAL COMMUNICATIONS		21
5.1 SERIAL PORT CONFIGURATION		21
5.2 COMMAND SYNTAX		21
5.3 COMMAND SUMMARY		22
5.4 COMMAND REFERENCE		23
5.4.1 CAUTO		23
5.4.2 CZERO		24
5.4.3 DACSTEP		25
5.4.4 O3		26
5.4.5 SETADDR		27
5.4.6 TDUMP		28
5.4.7 TLIST		29
5.4.8 VGET		30
5.4.9 VLIST		31
5.4.10 VSET		32
6.0 MAINTENANCE		33
6.1 REPLACING THE GAS FILTER ELEMENT (OPTIONAL)		33

P/N 03662D Teledyne API Model 460H O3 Monitor Operator Manual - Page iii

Image 3

Contents 03662 Rev. D 1/8/04 MODEL 460H NEMA OZONE MONITORINSTRUCTION MANUAL EMAIL api-sales@teledyne.comSAFETY MESSAGES I. 0 INTRODUCTION TABLE OF CONTENTS2.0 INSTALLATION 6.0 MAINTENANCE6.3 DEGREE OF PROTECTION 6.2 CLEANING EXTERIOR SURFACES OF THE M460H7.0 SENSOR AND SYSTEM TROUBLESHOOTING APPENDIX A - SERIAL PORT CONFIGURATIONElectrical Connections FIGURESFigure 2-1 Mounting Hole Locations Pneumatic ConnectionsSerial Port Configuration TABLESTable 2-1 Digital Status Output Pins Table 2-3 Serial Port Pins1.1 Preface I.0 INTRODUCTIONTERMS AND CONDITIONS 1.2 WARRANTY POLICYADVANCED POLLUTION INSTRUMENTATION DIVISION 02024c1.3 Principle of Operation 1.4 Specifications 2.0 Installation 2.1 Mechanical InstallationFigure 2-1 Mounting Hole Locations Figure 2-2 Pneumatic Connections 2.2 Pneumatic Connections2.3AC Power Connection I/O CONNECTOR 2.4 Electrical I/O Connections2.4.1 Analog Output Figure 2-3 Electrical ConnectionsName Table 2-1 Digital Status Output Pins2.4.2 Digital Status Outputs LabelDescription 2.4.3 Control InputsTable 2-2 Control Inputs InputRS232 Table 2-3 Serial Port Pins2.4.4 RS232/RS485 Serial Communications Port Figure 2-5 Typical RS232 and RS485 Connections3.0 Startup 4.1.2 Pressure Display 4.0 Operation4.1 Front Panel Display 4.1.1 O3 readout4.2.2 Auto-Zero Function 4.2.1 Auto-Zero Installation4.2.3 Auto Zero Error 4.2 Auto-Zero Operationaddresscommanddata1,data2#checksumCR 5.1 Serial Port Configuration5.2 Command Syntax Table 5-1 Serial Port ConfigurationTable 5-2 Serial Port Command Summary 5.3 Command SummaryExamples of valid Commands with no data Examples of valid Commands with dataData Parameters Sent 5.4 Command Reference5.4.1 CAUTO Syntax5.4.2 CZERO 5.4.3 DACSTEP 5.4.4 O3 addressO3CRaddresso3conc#checksumCR addressSETADDRnewaddressCR 5.4.5 SETADDR5.4.6 TDUMP 5.4.7 TLIST addressvarvalue#checksumCR 5.4.8 VGETAllowable Range Index5.4.9 VLIST 1VLISTCR#5 iirfilt = 0.4 #6 concunits = newvalue 5.4.10 VSETvarindex is index number for internal VAR See VGET for index list6.1 Replacing the gas filter element 6.0 Maintenance6.2 Cleaning Exterior Surfaces of the M460H Filter Replacement ProcedureTable 7-1 Digital Status Outputs 7.0 Sensor and System Troubleshooting7.1 Status Output Summary 7.2 Sensor OK7.3 Invalid Reading 7.4 Lamp Low7.5 Cell Dirty Invalid 7.6 Status Output Summary TableTable 7-2 Status Output Truth Table SensorAppendix A - Serial Port Configuration Figure A-1 RS232/RS485 Jumpers Controller PCA#03492RS232RS485 Appendix B - Pneumatic Diagram