Tyan Computer TYAN S1572 ATX user manual Entering Setup

Page 18

4. BIOS Configuration

Award's BIOS has a built in setup program that allows the user to modify the basic system configuration. This type of information is stored in the battery-backed CMOS NVRAM. Entering incorrect information or for- getting your password can lock you out of your system.(refer to 3.9 for resetting of CMOS)

4.1. Entering Setup

Power ON the computer and press <Del> immediately and you will enter Setup. The other way to enter setup is to power on the computer, when the below message appears briefly at the bottom of the screen during the POST (Power On Self Test), press <Del> key or simultaneously press <Ctrl>, <Alt>, and <Esc> keys.

*TO ENTER SETUP BEFORE BOOT PRESS CTRL-ALT- ESC OR DEL KEY

If the message disappears before you respond and you wish to enter Setup, restart the system by turning it OFF then ON or by pressing "Reset" on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt>, and <Del> keys. If you do not press the keys at the correct time, the system will not boot and an error message will appear on the screen. You will be asked to;

*PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER SETUP.

Figure 4.1 will appear on the sceen. The Main Menu allows you to select from the 8 setup functions and 2 exit choices. Use the arrow keys to select among the items and press <Enter> to accept or enter each sub-menu.

S1572-001-01 http://www.tyan.com

18

 

 

 

 

 

 

 

 

 

Image 18
Contents Tyan S1572 ATX Page Table Of Contents Introduction Hardware Specifications/Features Software Specifications EnvironmentBoard Installation On Board Resource Setting .1 S1572 ATX Board Layout CPUHeatsink Fan Power J18 CPU Speed Settings for Cyrix/SGS/IBM 6x86/M1/AMDDimm Memory Voltage Select 3V is Default JP23 CPU SpeedCmos Reset JP1Default Battery On Bios Voltage Select JP2 Default isCPU Select Default P54C, P55CMMX, & Cyrix J8 Jumper Block DescReset Connector J8 pin Keylock Connector J25Flash Eprom JP2 HDD LED J8 pins 13-14 and pins Port Setting J15 and J16Speaker Connector J8 pins Infra Red Interface J8 pins 8-11 and J2Speaker Connector Installation Hardware Reset Switch Connector InstallationHardware Cmos & Password Reset Refer to for Flash Eprom upgrade proceduresDram Installation CPU Installation Peripheral Device Installation Upgrading Cache MemoryEntering Setup To Enter Setup Before Boot Press CTRL-ALT- ESC or DEL KEYPress F1 to CONTINUE, CTRL-ALT-ESC or DEL to Enter Setup Control Keys Setup Page menu/Option Page Setup Menu Getting Help Main MenuWChipset features setup WStandard Cmos setupWBIOS features setup WPower Management setupStandard Cmos Setup Menu DateTime Primary/Secondary Drive Type Drive a type/Drive B typeHalt On VideoEGA/VGA MemoryExpanded Memory Other MemorySwap Floppy Drive Default value is Disabled Attempting to write to boot sector, continue? Y/NBoot Sequence Virus warningBoot Up Floppy Seek Boot Up NumLock Status Default value is OnGate A20 Option Chipset Features Screen Chipset Features SetupVideo Bios Shadow Security OptionWPM Control by APM Power Management SetupWPower Management WVideo Off MethodWDoze Mode WStandby ModeWReload Global Timer Events PCI Slot Configuration ROM ISA Bios PCI Slot Configuration Award SOFTWARE, INCLegacy ISA WResources Controlled ByWIRQ n assigned to PCI/ISA PnPIntegrated Peripherals Load Setup defaults Enter PasswordROM ISA Bios Cmos Setup Utility Award SOFTWARE, INC Password DisabledIDE HDD Auto Detection Flash Writer Utility Page Flash Memory Writer Utility Screen Award Flash Memory WriterDMA Channels Timer MAPSystem Resource NMI