Tyan Computer TYAN S1572 ATX user manual Video, Ega/Vga, Halt On, Memory

Page 24

wVideo

This category detects the type of graphics adapter used for the primary

display system. It must match your video display card and monitor. Al- though secondary monitors are supported, you do not have to select that type in setup.

EGA/VGA

Enhanced Graphics Adapter/Video Graphics Array.

 

For VGA,SVGA, or PGA monitor adapters.

CGA 40

Color Graphics Adapter, power up in 40 column mode.

CGA 80

Color Graphics Adapter, power up in 80 column mode.

Mono

Monochrome adapter, includes hi-res monochrome.

wHalt On

The category determines whether the computer will stop if an error is detected during power up.

No errors

Whenever the BIOS has detected a non-fatal error, the

 

system will be stopped and you will be promted.

All errors

The system boot will not be stopped for any errors that

 

are detected.

All, but Keyboard

The system boot will not stop for a keyboard error;it

 

will stop for all other errors.

All, but Diskette

The system boot will not stop for disk errors; it will

 

stop for all other errors.

All, but Disk/Key

The system boot will not stop for a keyboard or disk

 

error; it will stop for all other errors.

wMemory

The category is for display-only and it is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 640K.

Extended Memory

The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1MB in the CPU's memory address map.

S1572-001-01 http://www.tyan.com

24

 

 

 

 

 

 

 

 

 

Image 24
Contents Tyan S1572 ATX Page Table Of Contents Introduction Hardware Specifications/Features Software Specifications EnvironmentBoard Installation On Board Resource Setting .1 S1572 ATX Board Layout CPUCPU Speed Settings for Cyrix/SGS/IBM 6x86/M1/AMD Dimm Memory Voltage Select 3V is DefaultHeatsink Fan Power J18 JP23 CPU SpeedBios Voltage Select JP2 Default is CPU Select Default P54C, P55CMMX, & CyrixCmos Reset JP1Default Battery On J8 Jumper Block DescReset Connector J8 pin Keylock Connector J25Flash Eprom JP2 Port Setting J15 and J16 Speaker Connector J8 pinsHDD LED J8 pins 13-14 and pins Infra Red Interface J8 pins 8-11 and J2Speaker Connector Installation Hardware Reset Switch Connector InstallationHardware Cmos & Password Reset Refer to for Flash Eprom upgrade proceduresDram Installation CPU Installation Peripheral Device Installation Upgrading Cache MemoryEntering Setup To Enter Setup Before Boot Press CTRL-ALT- ESC or DEL KEYPress F1 to CONTINUE, CTRL-ALT-ESC or DEL to Enter Setup Control Keys Setup Page menu/Option Page Setup Menu Getting Help Main MenuWStandard Cmos setup WBIOS features setupWChipset features setup WPower Management setupStandard Cmos Setup Menu DateTime Primary/Secondary Drive Type Drive a type/Drive B typeVideo EGA/VGAHalt On MemoryExpanded Memory Other MemoryAttempting to write to boot sector, continue? Y/N Boot SequenceSwap Floppy Drive Default value is Disabled Virus warningBoot Up Floppy Seek Boot Up NumLock Status Default value is OnGate A20 Option Chipset Features Setup Video Bios ShadowChipset Features Screen Security OptionPower Management Setup WPower ManagementWPM Control by APM WVideo Off MethodWDoze Mode WStandby ModeWReload Global Timer Events PCI Slot Configuration ROM ISA Bios PCI Slot Configuration Award SOFTWARE, INCWResources Controlled By WIRQ n assigned toLegacy ISA PCI/ISA PnPIntegrated Peripherals Load Setup defaults Enter PasswordROM ISA Bios Cmos Setup Utility Award SOFTWARE, INC Password DisabledIDE HDD Auto Detection Flash Writer Utility Page Flash Memory Writer Utility Screen Award Flash Memory WriterTimer MAP System ResourceDMA Channels NMI