Tyan Computer TYAN S1572 ATX Attempting to write to boot sector, continue? Y/N, Virus warning

Page 26

wVirus warning

This category flashes on screen. During and after the system boot up, any attempt to write to the boot sector or the partition table of the hard disk drive will halt the system and the following error message will appear. In the meantime, you can run an anti-virus program to locate the problem. Default value is Enabled.

"Attempting to write to boot sector, continue? Y/N"

Enabled Activate automatically when the system boots up causing a warning message to appear when anything attemps to access the boot sector or hard disk partition table.

Disabled No warning message to appear when anything attemps to access the boot sector or hard disk partition table.

wCPU Internal Cache/External Cache

These two categories speed up the memory access. However, it de- pends on the CPU/Chipset design. Default value is Enabled.

Enabled Enables the cache

Disabled Disables the cache

wBoot Sequence

This category determines which drive the computer searches first for the disk operating system (i.e. DOS). Default value is A,C.

A,C

System will first search for floppy disk drive then hard disk drive.

C,A

System will first search for hard disk drive then floppy disk drive

wSwap Floppy Drive Default value is Disabled

Enabled Floppy A & B will be swapped under DOS

Disable Floppy A & B will be normal definition.

S1572-001-01 http://www.tyan.com

26

 

 

 

 

 

 

 

 

 

Image 26
Contents Tyan S1572 ATX Page Table Of Contents Introduction Hardware Specifications/Features Software Specifications EnvironmentBoard Installation On Board Resource Setting .1 S1572 ATX Board Layout CPUHeatsink Fan Power J18 CPU Speed Settings for Cyrix/SGS/IBM 6x86/M1/AMDDimm Memory Voltage Select 3V is Default JP23 CPU SpeedCmos Reset JP1Default Battery On Bios Voltage Select JP2 Default isCPU Select Default P54C, P55CMMX, & Cyrix J8 Jumper Block DescFlash Eprom JP2 Reset Connector J8 pinKeylock Connector J25 HDD LED J8 pins 13-14 and pins Port Setting J15 and J16Speaker Connector J8 pins Infra Red Interface J8 pins 8-11 and J2Speaker Connector Installation Hardware Reset Switch Connector InstallationHardware Cmos & Password Reset Refer to for Flash Eprom upgrade proceduresDram Installation CPU Installation Peripheral Device Installation Upgrading Cache MemoryPress F1 to CONTINUE, CTRL-ALT-ESC or DEL to Enter Setup Entering SetupTo Enter Setup Before Boot Press CTRL-ALT- ESC or DEL KEY Control Keys Setup Page menu/Option Page Setup Menu Getting Help Main MenuWChipset features setup WStandard Cmos setupWBIOS features setup WPower Management setupTime Standard Cmos Setup MenuDate Primary/Secondary Drive Type Drive a type/Drive B typeHalt On VideoEGA/VGA MemoryExpanded Memory Other MemorySwap Floppy Drive Default value is Disabled Attempting to write to boot sector, continue? Y/NBoot Sequence Virus warningGate A20 Option Boot Up Floppy SeekBoot Up NumLock Status Default value is On Chipset Features Screen Chipset Features SetupVideo Bios Shadow Security OptionWPM Control by APM Power Management SetupWPower Management WVideo Off MethodWReload Global Timer Events WDoze ModeWStandby Mode PCI Slot Configuration ROM ISA Bios PCI Slot Configuration Award SOFTWARE, INCLegacy ISA WResources Controlled ByWIRQ n assigned to PCI/ISA PnPIntegrated Peripherals Load Setup defaults Enter PasswordROM ISA Bios Cmos Setup Utility Award SOFTWARE, INC Password DisabledIDE HDD Auto Detection Flash Writer Utility Page Flash Memory Writer Utility Screen Award Flash Memory WriterDMA Channels Timer MAPSystem Resource NMI