Perle Systems 5500208-43 Options break, Break-length, Break-delay, Connection-method, Data-bits

Page 37

Line Commands

Options break

Specifies how a break is interpreted:

zoff—The IOLAN ignores the break key completely and it is not passed through to the host. This is the default setting.

zlocal—The IOLAN deals with the break locally. If the user is in a session, the break key has the same effect as a hot key.

zremote—When the break key is pressed, the IOLAN translates this into a telnet break signal which it sends to the host machine.

zbreak-interrupt—On some systems such as SunOS, XENIX, and AIX, a break received from the peripheral is not passed to the client properly. If the client wishes to make the break act like an interrupt key (for example, when the stty options

-ignbrk and brkintr are set).

break-length

The length of time (in milliseconds) for which the break signal will be asserted on the se- rial port. Valid values are 0-65535.

Default is 1000 ms

A value of 0 will cause the "request to send a break signal" to be ignored.

break-delay

The length of time (in milliseconds) to delay after a break signal is sent before the IOLAN sends data. Valid values are 0-65535.

Default: 0 ms ( no delay )

connection-method

Determines how a modem will work on the line. Select from the following options:

zDirect Connect—Indicates that there is not a modem on the line. This is the default.

zDial In—Specify this option when a user is remote and will be dialing in via modem or ISDN TA.

zDial Out—Specify this option when a modem is attached to the serial port and is being used to dial out.

zDial In/Out—Specify this option when the IOLAN is being used as a router (depending on which end of the link your IOLAN is situated and how you want to initiate the communication).

data-bits

Specifies the number of bits in a byte. The default is 8.

dial-timeout

The number of seconds the IOLAN will wait to establish a connection to a remote modem. The default value is 45 seconds.

dial-retries

The number of times the IOLAN will attempt to establish a connection with a remote modem. The default value is 2.

flowin

Determines if input flow control is to be used. Default is On. This is active only when Line Flow Control is set to Soft, Hard, or Both.

flowout

Determines if output flow control is to be used. Default is On. This is active only when Line Flow Control is set to Soft, Hard, or Both.

38

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands About This Book PrefaceIntended Audience Making a Technical Support Query Contacting Technical SupportFeedback on this Manual Repair ProcedureIntroduction Command SyntaxIntroduction CLI ConventionsCommand Options Command ShortcutsServer Commands Server CommandsSet Custom-App Set ServerDhcp/bootp Bypass-passwordDefault size 1500 bytes Domainname Default Interval 180 seconds. monitor-connection-timeoutPassword-limit Oem-loginTimeout Default Buffer Size 4 KB DS1/TS1/STS8DShow Custom-App Set ServiceShow Modbus Show ServerSet Ethernet Hardware CommandsShow Hardware Options Auto10-half10-full100-half100-fullSet Modbus Gateway Modbus CommandsSet TruePort Remap-Baud TruePort Baud CommandsShow TruePort Remapped-idSet IPv6 IPv6 CommandsShow IPv6 Set Custom-IPv6 Add Custom-IPv6Range Default Range Default 64 method manualDelete Custom-IPv6 Field Format IPv6 address prefix-bits manualCommands for Users Logged Into the Iolan User CommandsPing MenuResume ScreenSet User Session Set UserSyslog Console Show Line UsersShow Sessions Show TermtypeTcpport TelnetSet Default User Configuring UsersVersion Add UserLevel Hotkey-prefixService Line-accessSess-timer Phone-numberSet User Level Configureduser Show Default UserShow the settings for the specified user Show the settings for the current userPort vs -Port Line Commands Line CommandsLine Commands Set LineDial-timeout Break-delayOptions break Break-lengthData-logging Default Disabled initialInitiate-connection Internet-addressKeepalive ResetLine-name LockSession strings Default 10 ms Sess-timerStop-bits Term-typeSet Line Interface Confighost Set Line ServiceServerport Hostport Modemname Set ModemInitstring Options Program-command-line Line Service CommandsShow Line Options termtype Set Telnet-ClientOutboundport Set UDPStartipaddress EndipaddressSet Vmodem Set Vmodem-Phone Set Modbus-Master Line Set Modbus-Slave LineIpaddress HostSet Line Initiate-Connection Set Multihost LineShow Telnet-Client Show InterfaceShow UDP Show VmodemAdd Modem Modem CommandsDelete Modem Show ModemsSet Packet-Forwarding Line Packet Forwarding CommandsEnable-end-trigger2 Enable-end-trigger1Enable-end-eof1 Enable-end-eof2Show Packet-Forwarding Line Snmp Commands Network Commands ChapterAdd Community Add TrapDelete Trap Delete CommunitySet Snmp Set Snmp engine-id-string Set Snmp inform-timeoutSet Snmp inform-retries Show SnmpHosts Commands Tftp CommandsShow Hosts Gateway CommandsAdd Gateway Delete GatewaySet Gateway Description Configures the gateway User Level Admin SyntaxShow Gateways DestinationipSet Syslog Logging CommandsShow Syslog Time Commands Time CommandsTime/Date Setting Commands Show Date Bootup Commands Administration CommandsShow Bootup Set BootupConfiguration file Show ARPNetload Tftp File Transfer CommandsHostname/ipaddress FilenameOptions Factory-default-config Custom Factory DefaultNetsave Table or a DNS serverSet Motd CommandsSet Motd Show MotdConfiguration Statistics Statistic Commands ChapterShow Netstat Show Modbus StatisticsRun-Time Statistics Global I/O Commands O CommandsSet IO UDP Set Line Set IO Temperature-ScaleSet IO Failsafe Set IO ModbusSet IOChannel Set IOChannel ModeSet IOChannel Digital I/O Set IOChannel Digital InputSet IOChannel Digital Input Serial Pins Set IOChannel Digital Output Current status. The default is disabledDescription can be up to 20 characters Will be displayed as activeInactive-signal-width Active-signal-widthActive-to-inactive-delay Inactive-to-active-delaySet IOChannel Relay Set IOChannel Digital Output Serial PinsOptions description RelaynumberOptions analogchannel Set IOChannel Analog True AnalogTrigger-level Trigger-typeClear-mode Clear-levelSet IOChannel Analog Temperature Level Default Disabled keepalive EnabledSet IOChannel IOExtension Options channelClient-initiated multihost Client-initiated tcp-portServer-initiated tcp-port Local-connection inputchannelShow IOChannel Status Set IOChannel MultihostKill IOChannel ChannelShow IOChannel Show IODigital Output Channel Control CommandsDigital Input RelayGlossary

5500208-43 specifications

Perle Systems 5500208-43 is a highly advanced device in the realm of serial device connectivity and management. Designed to facilitate seamless communication between legacy serial devices and modern network infrastructure, this device serves as a reliable solution for numerous industrial and commercial applications.

One of the main features of the Perle 5500208-43 is its ability to connect up to 16 serial devices simultaneously over a single Ethernet connection. This multi-port capability is made possible through its robust architecture, allowing businesses to expand their network without the hassle of complex cabling. The device is equipped with 16 RS-232 serial ports, ensuring compatibility with a wide range of devices including printers, sensors, and legacy machines.

In terms of technologies, the 5500208-43 utilizes Perle’s advanced IOLAN technology which offers a host of features designed for efficiency and reliability. This technology not only ensures high-speed data transmission but also enables users to easily manage and configure the device through a user-friendly web interface. Furthermore, the device's support for various protocols, including TCP/IP, UDP, and SNMP, provides significant flexibility, allowing integration into existing IT infrastructures with ease.

Another notable characteristic of the Perle 5500208-43 is its rugged design. Built to withstand harsh environments, it is perfect for deployment in industrial settings where exposure to dust, humidity, and temperature variations can be a concern. The device supports industrial-grade power inputs, including PoE (Power over Ethernet), providing added convenience in installation and maintenance.

Security is also a top priority in the design of the 5500208-43. It incorporates features such as secure socket layer (SSL) encryption and user authentication to ensure that data remains protected during transmission. This makes it particularly suitable for applications requiring secure data handling, such as in healthcare, finance, and government sectors.

Additionally, the Perle 5500208-43 is backed by a solid warranty and technical support, giving customers peace of mind that they are investing in a reliable product. With its combination of versatility, durability, and advanced technology, this device stands out as a crucial component in bridging the gap between traditional serial devices and modern network systems.
Top Page Image Contents