Perle Systems 5500208-43 manual Channel Control Commands, Digital Output, Digital Input, Relay

Page 88

I/O Channel Control Commands

I/O Channel Control Commands

The I/O commands in this section are used to manually manage the I/O channels.

Digital Output

Description	Manages the Digital output channel status. Not all models have four digital channels,
User Level	most have just two.
User Level	Admin
Syntax	iochannel d1d2d3d4ctsdsrdcd clear alarminput-latch
Options	alarm
	Clears the alarm. Note that if the condition that tripped the alarm still exists, the alarm
	will not look like it’s cleared, but will reflect the appropriate alarm level severity.
	Alarm Level 0 means that the alarm has not been triggered.
	latch-input
	Clears the latch value.

Digital Input

Description	Manages the Digital input channel status.
User Level	Admin
Syntax	iochannel d1d2d3d4rtsdtr output activatedeactivate
Option	output
	Manually deactivates the I/O channel.

Relay

Description	Manages the Relay output channel status.
User Level	Admin
Syntax	iochannel r1r2 output activatedeactivate
Option	output
	Manually deactivates the I/O channel.

Analog Input

Description	Manages the Analog input channel status.
User Level	Admin
Syntax	iochannel a1a2a3a4 clear alarmminmax
Options	alarm
	Clears the alarm. Note that if the condition that tripped the alarm still exists, the alarm
	will not look like it’s cleared, but will reflect the appropriate alarm level severity.
	Alarm Level 0 means that the alarm has not been triggered.
	min
	Clears the minimum value.
	max
	Clears the maximum value.

89	IOLAN DS1/TS2 CLI Reference Guide, Version 4.3

Image 88

Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands About This Book PrefaceIntended Audience Contacting Technical Support Making a Technical Support QueryRepair Procedure Feedback on this ManualCommand Syntax IntroductionIntroduction CLI ConventionsCommand Shortcuts Command OptionsServer Commands Server CommandsSet Custom-App Set ServerBypass-password Dhcp/bootpDefault size 1500 bytes Domainname Default Interval 180 seconds. monitor-connection-timeoutOem-login Password-limitTimeout Default Buffer Size 4 KB DS1/TS1/STS8DSet Service Show Custom-AppShow Modbus Show ServerHardware Commands Set EthernetShow Hardware Options Auto10-half10-full100-half100-fullModbus Commands Set Modbus GatewayTruePort Baud Commands Set TruePort Remap-BaudShow TruePort Remapped-idSet IPv6 IPv6 CommandsShow IPv6 Add Custom-IPv6 Set Custom-IPv6Range Default 64 method manual Range DefaultDelete Custom-IPv6 Field Format IPv6 address prefix-bits manualUser Commands Commands for Users Logged Into the IolanMenu PingResume ScreenSet User Set User SessionShow Line Users Syslog ConsoleShow Sessions Show TermtypeTelnet TcpportConfiguring Users Set Default UserVersion Add UserHotkey-prefix LevelLine-access ServiceSess-timer Phone-numberSet User Level Show Default User ConfigureduserShow the settings for the specified user Show the settings for the current userLine Commands Port vs -Port Line CommandsLine Commands Set LineBreak-delay Dial-timeoutOptions break Break-lengthDefault Disabled initial Data-loggingInitiate-connection Internet-addressReset KeepaliveLine-name LockDefault 10 ms Sess-timer Session stringsStop-bits Term-typeSet Line Interface Confighost Set Line ServiceServerport Hostport Modemname Set ModemInitstring Options Program-command-line Line Service CommandsShow Line Set Telnet-Client Options termtypeSet UDP OutboundportStartipaddress EndipaddressSet Vmodem Set Vmodem-Phone Set Modbus-Slave Line Set Modbus-Master LineIpaddress HostSet Multihost Line Set Line Initiate-ConnectionShow Interface Show Telnet-ClientShow UDP Show VmodemModem Commands Add ModemDelete Modem Show ModemsPacket Forwarding Commands Set Packet-Forwarding LineEnable-end-trigger1 Enable-end-trigger2Enable-end-eof1 Enable-end-eof2Show Packet-Forwarding Line Network Commands Chapter Snmp CommandsAdd Community Add TrapDelete Trap Delete CommunitySet Snmp Set Snmp inform-timeout Set Snmp engine-id-stringSet Snmp inform-retries Show SnmpTftp Commands Hosts CommandsGateway Commands Show HostsAdd Gateway Delete GatewayDescription Configures the gateway User Level Admin Syntax Set GatewayShow Gateways DestinationipSet Syslog Logging CommandsShow Syslog Time Commands Time CommandsTime/Date Setting Commands Show Date Administration Commands Bootup CommandsSet Bootup Show BootupConfiguration file Show ARPTftp File Transfer Commands NetloadHostname/ipaddress FilenameCustom Factory Default Options Factory-default-configNetsave Table or a DNS serverMotd Commands SetSet Motd Show MotdStatistic Commands Chapter Configuration StatisticsShow Netstat Show Modbus StatisticsRun-Time Statistics Global I/O Commands O CommandsSet IO UDP Set IO Temperature-Scale Set LineSet IO Failsafe Set IO ModbusSet IOChannel Mode Set IOChannelSet IOChannel Digital I/O Set IOChannel Digital InputSet IOChannel Digital Input Serial Pins Current status. The default is disabled Set IOChannel Digital OutputDescription can be up to 20 characters Will be displayed as activeActive-signal-width Inactive-signal-widthActive-to-inactive-delay Inactive-to-active-delaySet IOChannel Digital Output Serial Pins Set IOChannel RelayOptions description RelaynumberSet IOChannel Analog True Analog Options analogchannelTrigger-type Trigger-levelClear-mode Clear-levelSet IOChannel Analog Temperature Level Enabled Default Disabled keepaliveSet IOChannel IOExtension Options channel Client-initiated tcp-port Client-initiated multihost Server-initiated tcp-port Local-connection inputchannelSet IOChannel Multihost Show IOChannel StatusKill IOChannel ChannelShow IO Show IOChannelChannel Control Commands Digital OutputDigital Input RelayGlossary